Initial Operation; Switching On And Off - Bosch GLL3-80 Instrucciones De Funcionamiento Y Seguridad

Ocultar thumbs Ver también para GLL3-80:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Initial Operation
• Loud audio signals will sound under
certain conditions while operating the
tool. Therefore, keep the tool away from
your ear or other persons. The loud audio
signal can cause hearing damage.
Protect the tool against moisture and
direct sun light.
• Do not subject the tool to extreme
t e m p e r a t u r e s o r v a r i a t i o n s i n
temperature. As an example, do not leave
it in vehicles for longer periods. In case of
large variations in temperature, allow the
tool to adjust to the ambient temperature
before putting it into operation. In case of
extreme temperatures or variations in
temperature, the accuracy of the tool can
be impaired.
• Avoid heavy impact or dropping of the
tool. After heavy exterior impact on the
tool, an accuracy check should always be
carried out before continuing to work (see
"Leveling Accuracy").
• Switch the tool off during transport.
When switching off, the leveling unit, which
can be damaged in case of intense
movement, is locked.
Switching On and Off
To switch on the tool, slide the On/Off switch
7 to the "
on". position (when working
without automatic levelling) or to the "
on" position (when working with automatic
levelling). Immediately after switching on,
the tool sends laser beams out of the exit
openings 1.
• Do not point the laser beam at persons
or animals and do not look into the laser
beam yourself, not even from a large
distance.
To switch off the tool, slide the On/Off switch
7 to the " off " position. When switching off,
the levelling unit is locked.
When exceeding the maximum permitted
operating temperature of 40°C, the tool
switches off to protect the laser diode. After
cooling down, the tool is ready for operation
and can be switched on again.
Deactivating the Automatic Shut-off
When no button on the tool is pressed for
approx. 30 minutes, the tool automatically
switches off to save the batteries.
All manuals and user guides at all-guides.com
Operation
To switch on the tool after automatic shut-off,
either slide the On/Off switch 7 to the "off"
position and then switch the tool on again or
press the operating mode button 4 once or
press the pulse-function button 3 once.
To deactivate the automatic shut-off, keep the
operating mode button 4 pressed for at least 3
s (while the tool is switched on). Deactivation
of the automatic shut-off is confirmed by brief
flashing of the laser beams.
• Do not leave the switched on tool
unattended and switch the tool off after
use.
To activate the automatic shut-off, switch the
tool off and then on again.
Deactivating the Signal Tone
After the tool has been switched on,the audio
signal is always activated.
To deactivate/activate the audio signal, press
and hold the operating mode button 4 and
the pulse-function button 3 at the same time
for at least 3 s.
The audio signal activation and deactivation
are both confirmed by three short beeps.
The tool has several operating modes
between which you can switch at any time:
– Generating a horizontal laser plane,
– Generating a vertical laser plane,
– Generating two vertical laser planes,
– Generating a horizontal laser plane as
After switching on, the tool generates
a horizontal laser plane. To change the
operating mode, press the operating mode
button 4.
All operating modes can be selected with or
without automatic leveling.
Pulse Function
When working with the laser receiver 17,
the pulse function must be activated, –
independent of the selected operating mode.
In pulse function, the laser lines flash at very
high frequency and thus become detectable
by the laser receiver 17.
To switch on the pulse function, press button
3. When the pulse function is switched
on, the pulse-function indicator 5 lights up
green. When the pulse function is switched
on, the visibility of the laser lines is reduced
-8-
Operating Modes
well as two vertical laser planes.
Tabla de contenido
loading

Este manual también es adecuado para:

3 601 k63 310

Tabla de contenido