ADDITIONAL SAFETY INSTRUCTIONS
1. This tool is designed to be used as a polisher. Read all the
warnings, instructions, indications provided on drawings
and specifications supplied with this tool. Failure to comply
with all the instructions provided may cause electrical shocks,
fire and/or serious injuries.
2. This tool is not intended to be used for smoothing, metal
brushing and cutting operations. The use of this tool for
unintended applications may cause hazards and injuries to
people.
3. The tool must be used with accessories that have
been specifically designed or recommended by the
manufacturer. The fixing of the accessory to the tool does
not guarantee a safe operation; read the following additional
instructions.
4. The rated speed of the accessories must be at least
equivalent to the maximum speed specified on the tool.
Using the accessories at speeds above the rated one, may
cause them to break or be projected into the air.
5. The external diameter and thickness of the accessories
must match the specifications of the tool. Accessories
with incorrect dimensions cannot be adequately protected or
controlled.
6. The configuration of accessories must match the tool.
The use of accessories that cannot be perfectly fitted on the
tool may result in imbalance, excessive vibrations and in the
impossibility of controlling the tool.
7. Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verify
there are no cracks, tears or excessive wear. If the tool
or accessory has fallen, verify that they are not damaged
or install a new accessory. After inspecting or installing
an accessory, test the operation of the tool at maximum
speed and without load for one minute, keeping at a safety
distance. If the accessories are damaged, they will break
during this test.
8. Wear personal protective equipment. Depending on
application, use face shield,safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or
respirator must be capable of filtrating particles generated by
your operation. Prolonged exposure to high intensity noise may
cause hearing loss.
9. Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate
area of operation.
10.Hold power tool by insulated surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of the
power tool "live" and shock the operator.
11.Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning accessory.
12.Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may grab
the surface and pull the power tool out of your control.
4
13.Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
14.Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical hazards.
15.Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
16.Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or
shock.
Further Safety Instructions for All Operations
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or anyother accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the binding.
For example, if a polishing mop is snagged or pinched by the
workpiece, the edge of the mop that is entering into the pinch
point can dig into the surface of the material causing the mop
to climb out or kick out. The mop may either jump toward or
away from the operator, depending on direction of the mop's
movement at the point of pinching. Polishing mops may also
break under these conditions.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:
1) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start up.
The operator can control torque reaction or kickback forces, if
proper precautions are taken.
2) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
3) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool
in direction opposite to the wheel's movement at the point of
snagging.
4) Use special care when working corners, sharp edges,
etc. Avoid bouncing and snagging the accessory. Corners,
sharp edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
5) Do not attach a saw chain woodcarving blade or toothed
saw blade. Such blades create frequent kickback and loss of
control.
Additional Specific Safety Instructions for Polishers
• Always use eye protection. All users and bystanders must
wear eye protection that conforms to ANSI Z87.1.
• Clean out your tool often, especially after heavy use. Dust
and grit containing metal particles often accumulate on interior
surfaces and could create an electric shock hazard.
• Do not operate this tool for long periods of time. Vibration
caused by the operating action of this tool may cause
permanent injury to fingers, hands and arms. Use gloves to
provide extra cushion, take frequent rest periods and limit daily
time of use.
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving
parts.