Important - EINHELL GP-CM 36/47 S HW Li Manual De Instrucciones

Insert the mulching blade only when the machine
has been switched off , the safety plug (12) has
been pulled out and the batteries (16) removed.
To use the mulching function, disconnect the
catch bag, slide the mulching adaptor (Fig. 5d/
Item 18) through the ejector opening and close
the ejector fl ap again.
Rear ejector (Fig. 14)
To use the rear ejector function you must open
the ejector fl ap (Fig. 14/Item 7) slightly. Lock it in
place with the locking lever. Swing up the locking
lever and insert its foot into the recess provided.
The mulching adapter (Item 18) is not allowed to
be fi tted when the rear ejector is used.
Side ejector (Fig. 15b)
You must fi t the mulching adapter (18) in order to
use the side ejector. Hook in the side ejector ad-
apter (19) as shown in Fig. 15b.
Charging the battery (Fig. 21)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(17) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (16) into the battery
charger (17).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
Anl_GP_CM_36_47_S_HW_Li_SPK13.indb 26
GB
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Installing the battery (Fig. 22)
Open the battery cover (Item 4). Then insert the
batteries in the mounts as shown in Fig. 22.
For optimum mowing results and battery power
performance it is always best to use batteries
with the same capacity of 3.0 Ah or higher. There
is also the option of using batteries with diff erent
capacities in the two battery mounts A and B (Fig.
2) which are opposite each other.
Always make sure, however, that you only use
batteries of the same capacity in each separate
battery bank (Fig. 27).
For example, you could use 2 x 4.0Ah batteries in
one battery bank while using 2 x 3.0Ah batteries
in the opposite battery bank.

Important!

Use only batteries which are charged to the same
level. Never combine full and half-full batteries. Al-
ways charge the two/all batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two/all
batteries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Battery capacity indicator (Fig. 20)
Press the button for the battery capacity indicator
(Fig. 20/Item A). The battery capacity indicator
(Fig. 20/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
- 26 -
25.08.2021 13:14:23