Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17

Enlaces rápidos

SERIES 88H–EU HORIZONTAL AIR GRINDERS
Series 88H–EU Grinders are designed for metal removal in foundry work and similar
applications.
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state, federal
and country), that may apply to hand held/hand
operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the inlet
with 3/4" (19 mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Tool accessories may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
03530334
Form P6501–EU
Edition 10
August, 2000
GB
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 88H–EU Serie

  • Página 17: Amoladoras Neumáticas Horizontales De La Serie 88H-Eu

    03530334 Impreso P6501–EU Edición 10 Agosto, 2000 AMOLADORAS NEUMÁTICAS HORIZONTALES DE LA SERIE 88H–EU NOTA Las amoladoras de la serie 88H–EU están diseñadas para eliminación de metal en trabajos de fundición y aplicaciones similares. Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll–Rand.
  • Página 18: Etiquetas De Aviso

    ETIQUETAS DE AVISO AVISO EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR LESIONES. ADVERTENCIA ADVERTENCIA ADVERTENCIA Cortar siempre el suministro Use siempre protección para Use siempre protección ocular de aire y desconectar la man- los oídos cuando utilice esta guera de suministro de aire cuando utilice esta herramienta herramienta.
  • Página 19: Para Poner La Herramienta En Servicio

    AVISOS ESPECÍFICOS SOBRE LA AMOLADORA AVISO: Combinaciones incorrectas de rueda de rectificación, protector de rueda y velocidad de herramienta puedan resultar en lesionamientos. Las combinaciones correctas se especifican a continuación: Número de Pieza del Tipo de Rueda Diámetro de Rueda Grosor Máximo de Velocidad Máxima Protector...
  • Página 20: Declaración De Conformidad

    DECLARACIÓN DE CONFORMIDAD Ingersoll–Rand, Co. os abajo firmantes (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Amoladoras neumáticas horizontales de la serie 88H–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662...
  • Página 25 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Company Ingersoll–Rand Nederland Produktieweg 10 510 Hester Drive 2382 PB Zoeterwoude White House Nederland TN 37188 Tel: (31) 71 452200 Fax: (31) 71 5218671 Tel: (615) 672 0321 Fax: (615) 672 0801 Ingersoll–Rand Company SA PO Box 3720...
  • Página 48 Servicentre Servicecenter Servicesenter Huoltokeskus Centros de Assistência Técnica Ingersoll–Rand Company Ingersoll–Rand Nederland Produktieweg 10 510 Hester Drive 2382 PB Zoeterwoude White House Nederland TN 37188 Tel: (31) 71 452200 Fax: (31) 71 5218671 Tel: (615) 672 0321 Fax: (615) 672 0801 Ingersoll–Rand Company SA PO Box 3720 Ingersoll–Rand...

Este manual también es adecuado para:

88hl90l10–eu88hl60h106–eu

Tabla de contenido