Tabla de contenido
Idiomas disponibles
Idiomas disponibles
KEY DIMENSIONS
AND SPECIFICATIONS
Description
Front-Loading
Washer
Rated Voltage/Frequency
120VAC, 60Hz
Dimensions
27 in. (W) X 29 3,,_in. (D) X 38 11/16in. (H), 51 in. (D, door open)
68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.5 cm (D, door open)
Net Weight
196.2 Ib (89kg)
CHOOSE
THE PROPER LOCATION
WARNING
oThis washer is heaw/. Two or more people are
required when
moving and unpacking the washer.
Failure to do so may result in damage to property
or
serious bodily
harm.
• Store and install the washer where it will not be
exposed to temperatures
below freezing or exposed
to outdoor weather conditions. Failure to follow this
warning
can cause serious injury, fire, electric shock,
or death.
• Properly ground the washer to conform with all
electric governing codes and ordinances. Failure
to follow this warning
can cause serious injury, fire,
electric
shock, or death.
°To reduce the risk of electric
shock, do not install the
washer in humid spaces. Failure to follow this warning
can cause serious injury, fire, electric shock, or death.
•To ensure proper air flow, do not block the large
opening on the bottom of the washer with carpeting
or other materials.
• Do not remove the ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3-prong
outlet.
Failure to follow this warning
can cause
serious injury, fire, electric
shock, or death.
NOTE: Installing the washer in a humid space, or
installing or storing the washer where it will be exposed
to the weather or freezing
temperatures,
may result in
rust or other damage
that is not covered by the product
warranty.
Power Outlet
•The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
•The appliance
and outlet must be positioned
so that
the plug is easily accessible.
• Do not overload
the outlet with more than
one appliance.
•The outlet must be grounded
in accordance
with
current wiring electric
codes and regulations.
• Time-delay
fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility
and obligation
of
the product owner to have a proper outlet installed by a
qualified
service technician.
FLOORING
•To minimize
noise and vibration, the washer MUST be
installed on a solidly constructed
floor. See the NOTE
to your right.
•Allowable
slope under the entire washer is a maximum
1 in. difference
from side to side or from front to back.
• Installing on carpeting
and soft tile surfaces is
not recommended.
• Never install the washer on a platform
or weakly
supported
structure.
7
CLEARANCES
21 1/4"
_(54
cm)_1
i
"41
J_ I
29 3/4"
_
J_
4"
(75.6
¢m)
(10 cm)
51"
(129.5 cm)
To ensure sufflcient clearance
for water lines and airflow,
allow minimum clearances of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or floor moldings that may increase the
required clearances.
1
27
1
(2.5 cm)
(68.6 cm)
(2.5 cm)
Allow at least 22 in. (55.9 cm) in front of
the washer to open the door.
NOTE: The floor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without
flexing or bouncing.
If your floor has too much
flex, you may need to reinforce
it to make it more rigid.
A floor that is adequate
for a top-loading
washer may
not be rigid enough for a front loading washer, due to
the difference
in the spin speed and direction.
If the
floor is not solid, your washer may vibrate
and you may
hear and feel the vibration
throughout
your house.
Tabla de contenido
