Bosch Professional GWS 880 Manual Original página 18

18 | English
(20) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding
spindle
Restart protection
Weight according to EPTA-Procedure 01:2014
– with low-vibration auxiliary
handle
– with standard auxiliary
handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 93
dB(A); sound power level 104 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a = 7.5 m/s , K = 1.5 m/s ,
h
Disc sanding:
2 2
a = 7.5 m/s , K = 1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
1 609 92A 3FT | (12.02.2021)
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting
GWS 880
Fitting Protective Equipment
3 601 C96 0..
Pull the plug out of the socket before carrying out any
u
W 880
work on the power tool.
W 450
Note: If the grinding disc breaks during operation or the
-1
min 11,000
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
mm 115/125
vice immediately; see the "After-Sales Service and Applica-
M 14
tion Service" section for addresses.
mm 22
Protective guard for grinding
Place the protective guard (6) on the spindle collar. Adjust
●
the position of the protective guard (6) to meet the require-
ments of the operation. Lock the protective guard (6) by
kg 2.0
tightening the locking screw (7) using the combination
wrench (4).
kg 1.9 Adjust the protective guard (6) such that sparking in
u
the direction of the operator is prevented.
Note: The coding cams on the protective guard (6) ensure
/ II
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
Always use the protective guard for cutting (13) when
u
cutting with bonded abrasives.
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (13) is fitted in the same
way as the protective guard for grinding (6).
Side handle
Do not operate your power tool without the side
u
handle (3).
Screw the side handle (3) on the left or right of the machine
head depending on how your are working.
Hand guard
Always fit the hand guard (15) when working with the
u
rubber sanding plate (16) or with the cup brush/disc
brush/flap disc.
Attach the hand guard (15) to the side handle (3).
Fitting the abrasive tools
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Clean the grinding spindle (5) and all the parts to be fitted.
Lock the grinding spindle with the spindle lock button (1)
before clamping and releasing the abrasive tools.
Bosch Power Tools