Schumacher Electric INSTANT POWER XP2260W Manual Del Usuario página 6

USING THE AIR COMPRESSOR
WARNING. Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer's recommended
pressures. Do not leave the air compressor
unattended during use.
NOTE: Wrap cleats are provided for
convenient storage of the air compressor
hose. Wrap the hose around these cleats
when the hose is not in use.
1. Remove the air compressor hose from
the storage cleats.
2. Connect the adaptor to the valve stem
and close the thumb latch. If necessary,
use one of the additional adaptors.
3. Turn ON the inflator power switch and
inflate to the desired pressure or fullness.
4. When the desired pressure is reached,
put the inflator power switch to OFF,
open the thumb latch and remove the
connector from the valve stem.
5. Allow unit to cool.
6. Recharge the unit before storing.
NOTE: The air compressor is rated for
150 PSI maximum.
USING THE INFLATOR
RISK OF EXPLOSION.
Read instructions of the product being
inflated before using the inflator. Avoid
overinflation, do not exceed the
manufacturer's recommended pressures. Do
not leave the inflator unattended during use.
1. Ensure the battery clamps are securely
on the storage holders.
2. Attach the corrugated hose with end
adapter to the high-flow inflator outlet
located near the Compressor/Inflator
switch on the back of the Instant Power.
3. The main accessory adapter attached to
the corrugated hose accommodates up
to 4 sizes. If another size is needed, an
additional adapter can be attached to the
end of the main accessory adapter.
4. Insert the adapter into the product to be
inflated.
5. Push the Compressor/Inflator switch to the
INFLATOR position and inflate the product.
6. When the product is inflated to the
desired level, push the Compressor/
Inflator switch to the OFF position and
remove the adapter.
Estimated time for inflating
Vehicle tires 13-16"
Bike tires
Sports balls
These times are approximate. Use the air
compressor gauge to ensure the proper pressure
has been reached. Do not overinflate.
USING THE DEFLATOR
1. Ensure the battery clamps are securely
on the storage holders.
2. Attach the corrugated hose with the end
adapter to the high-flow deflator outlet,
which is located on the side of the
Instant Power.
3. The main accessory adapter attached to
the corrugated hose accommodates up
to 4 sizes. If another size is needed, an
additional adapter can be attached to the
end of the main accessory adapter.
4. Insert the adapter into the item to be
deflated.
5. Push the Compressor/Inflator switch to the
INFLATOR position and deflate the item.
6. When the product is deflated to the
desired level, push the Compressor/
Inflator switch to the OFF position and
remove the adapter.
BEFORE USING THE INVERTER
Important Safety Instructions:
1. Keep the Instant Power well ventilated, in
order to properly disperse heat generated
while it is in use. Make sure there are
several inches of clearance around the
top and sides, and do not block the vents
on the back of the Instant Power.
2. Make sure the Instant Power is not close
to any potential source of flammable
fumes or clothing.
3. Keep the Instant Power dry.
4. DO NOT allow the Instant Power to come
into contact with rain or moisture.
5. DO NOT operate the Instant Power if
you, the Instant Power, the device being
operated or any other surfaces that may
come in contact with any power source
are wet. Water and many other liquids
can conduct electricity, which may lead to
serious injury or death.
6. Do not place the Instant Power on or near
heating vents, radiators or other sources
of heat.
7. Do not place the Instant Power in direct
sunlight. The ideal air temperature for
operation is between 50° and 80° F.
6
• •
6-24 minutes
1-3 minutes
30 seconds