Attaching The Grinding Wheel - Metabo W 1100-115 Instrucciones De Manejo

SYMBOLS ON THE TOOL:
.......... Class II Construction
V ............. volts
A ............. amperes
Hz ........... hertz
.../min...... revolutions per minute
~ ............. alternating current
............ alternating current /direct current
n.............. rated speed
4. Overview
See page 2.
1 Support flange
2 Spindle
3 Spindle locking button
4 Sliding on/off switch *
5 Thumbwheel for selection of speed *
6 Lock (to prevent the machine from being switched
on unintentionally, or for continuous operation) *
7 Trigger ( for switching on and off) *
8 Additional handle
9 Safety cover
10 Clamping nut
11 2-hole spanner
12 Clamping screw
13 Lever for safety guard attachment *
* depending on equipment/not in scope of delivery
5. Commissioning
Before plugging in, check to see that the rated
mains voltage and mains frequency,
as stated on the rating label, match your power
supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
5.1 Attaching the additional handle
Always work with the additional handle
attached (8)! Attach the additional handle
on the left or right of the machine and secure.
5.2 Install safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 10.
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
W 1100...:
See page 2, illustration C.
- Slacken the screw (12). Place the safety guard (9)
in the position indicated.
- Turn the safety guard until the closed section is
facing the operator.
- Tighten the screw (12), ensuring that the anti-twist
device engages in the slots.
- Make sure that the guard is seated securely: you
should not be able to turn the safety guard.
WP 1200...RT, WE 1500...RT, WEV 1500...RT:
See page 2, illustration D.
- Pull on the lever (13). Place the safety guard (9) in
the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Pull on the (13)lever and turn the safety guard until
the closed section is facing the operator.
- Make sure that the guard is seated securely: the
lever must engage and you should not be able to
turn the safety guard.

6. Attaching the grinding wheel

Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work
(see chapter 10. Accessories).
6.1 Locking the spindle
- Press in the spindle locking button (3) and turn the
spindle (2) by hand until the spindle locking button
engages.
6.2 Placing the grinding wheel in position
See page 2, illustration A.
- Place the supporting flange (1) on the spindle (see
illustration above). The flange should not turn on
the spindle when properly attached.
- Place the grinding wheel on the
support flange (1) (see illustration above).
The grinding wheel must lay flat on the supporting
flange. The metal flange on the parting grinder
disc must lay flat on the support flange.
Note: The support flange (1) is secured to prevent it
from falling off. To remove: use some force if
necessary.
6.3 Securing/releasing the clamping nut
Securing the clamping nut (10):
The 2 sides of the clamping nut are different. Screw
the clamping nut onto the spindle as follows:
See page 2, illustration B.
- A) For thin grinding wheels:
The edge of the clamping nut (10) faces upwards
so that the thin grinding wheel can be attached
securely.
B) For thick grinding wheels:
The edge of the clamping nut (10) faces
downwards so that the clamping nut can be
attached securely to the spindle.
ENGLISH en
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
9