Bosch GBH 4-32 DFR Professional Instrucciones De Servicio página 18

OBJ_BUCH-337-001.book Page 18 Monday, May 7, 2007 10:34 AM
Firmly hold the retaining ring of the keyless replace-
ment chuck 12. Open the keyless replacement chuck
by turning the front sleeve in the direction of the sym-
bol " ".
Insert the drilling tool into the keyless replacement
chuck 12. Firmly hold the retaining ring of the keyless
replacement chuck 12 and turn the front sleeve in the
direction of the symbol "
Check the tight seating by pulling the tool.
Note: If the tool holder was opened to the stop, then
the latching noise possibly may be heard while closing
the tool holder and the tool holder will not close.
In this case, turn the front sleeve 13 once in the oppo-
site direction of the arrow. Afterwards, the tool holder
can be closed (tightened) again.
Turn the mode selector switch 5 to the "drilling" posi-
tion.
Removing Drilling Tools without SDS-plus
(see figure E)
Firmly hold the retaining ring of the keyless replace-
ment chuck 12. Open the keyless replacement chuck
by turning the front sleeve in the direction of the sym-
bol " ".
Remove the drilling tool.
Dust Extraction with the Dust Extrac-
tion Attachment (Accessory)
Mounting the Dust Extraction Attachment
(see figure F)
For dust extraction, the dust extraction attachment
(accessory) is required. When drilling, the dust extrac-
tion attachment retracts so that the attachment head
is always close to the surface at the drill hole.
Press the button for depth stop adjustment 9 and
remove the depth stop 11. Press button 9 again and
insert the dust extraction attachment into the auxiliary
handle 10 from the front.
Connect an extraction hose (diameter 19 mm, acces-
sory) to the extraction sleeve 15 of the dust extraction
attachment.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimen-
tal to health or carcinogenic, use a special vacuum
cleaner.
18 | English
Adjusting the Drilling Depth on the Dust Extrac-
tion Attachment (see figure G)
The required drilling depth X can also be adjusted
when the dust extraction attachment is mounted.
Insert the SDS-plus drilling tool to the stop into the
SDS-plus tool holder 1. Otherwise, the movability of
the SDS-plus drilling tool can lead to incorrect adjust-
".
ment of the drilling depth.
Loosen the wing bolt 19 on the dust extraction attach-
ment.
Without switching the power tool on, apply it firmly to
the drilling location. The SDS-plus drilling tool must
face against the surface.
Position the the guide pipe 20 of the dust extraction
attachment in its holding fixture in such a manner that
the head of the dust extraction attachment faces
against the surface to be drilled. Do not slide the
guide pipe 20 further over the telescopic pipe 18 of
the dust extraction attachment than required, so that
as much as possible of the scale 18 on the telescopic
pipe remains visible.
Retighten the wing bolt 19 again. Loosen the clamp-
ing screw 16 on the depth stop of the dust extraction
attachment.
Move the depth stop 17 on the telescopic pipe 18 in
such a manner that the clearance X shown in the fig-
ure corresponds with the required drilling depth.
Tighten the clamping screw 16 in this position.
Operation
Starting Operation
Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
Setting the Operating Mode
The operating mode of the power tool is selected with
the mode selector switch 5.
Note: Change the operating mode only when the
machine is switched off! Otherwise, the machine can
be damaged.
1 619 929 774 • 7.5.07