IPC SG-45 Manual De Instrucciones página 13

directly towards the sealed points of the glazed surfaces.
When outside temperatures are low, particularly during winter,
heat the surface of the glass by lightly steaming the entire
surface before cleaning. This compensates for the difference
in temperature between the internal and external surfaces,
reducing the surface tensions which might otherwise cause
the glass to break.
USING THE STEAM GENERATOR
Control panel (fig. 5).
A - Main switch 0-I.
B - Steam switch.
C - Solution injection pump switch.
D - Clean water tank level indicator.
E - Steam ready indicator.
F - Steam flow regulator.
Controls on hand grip (fig. 6).
G - Steam switch.
H - Solution injection pump button.
I - Steam button.
Turning the steam generator on:
The steam generator is turned on via the main switch A. In
the "I" position (fig. 5), the steam production boiler filler pump
is activated.
Steam phase.
Operate the steam switch "B". This turns on the power to the
steam production boiler. The appliance is ready to use when the
indicator light "E" on the control panel lights up (fig. 5).
Light "E" flashes when the minimum operating pressure is
reached and remains on until maximum operating pressure is
reached. You are recommended to wait until maximum pressure
is reached before starting work.
To activate steam emission, use the switch "G" and button "I"
on the handgrip. (fig.6)
Filling the cleaning product circuit.
Activate the detergent button "C/H" with the steam switch "G/I"
activated. Detergent is only delivered when the appliance is in
"steam ready" status (light "E" on the control panel lit).
The detergent circuit is filled with switches "C/H" activated and
steam regulation knob "F" in the "0" position.
This is only necessary when delivering the detergent for the
first time.
When the detergent in the tank runs out, the appliance emits
an intermittent beep.
If necessary, release pressure in the boiler by activating the
steam switch "G/I" with the main switch in the "l" position and
switch "B" in the "0" position.
The quantity of steam delivered can be adjusted using the knob
"F" on the control panel.
Rotate anticlockwise from positions 1 to 6 for maximum de-
livery.
Rotate clockwise from positions 6 to 1 for minimum delivery
(fig. 7).
When tank is empty, the light "D" comes on and the appliance
emits a continuous beep (fig. 5) when the steam switch is
operated.
To deliver detergent, use switch "C" (fig. 5) on the control
English
panel and button "H" on the handgrip (fig. 6). Detergent is only
delivered when the appliance is in "steam ready" status (light
"E" on the control panel lit).
Press the button until the product comes out of the attachment
and then at intervals of a couple of seconds to avoid affecting
the efficiency of the steam.
Combined steam/detergent phase.
Select the most suitable attachments.
- Floor brush for use with the extension tubes.
- Multipurpose rectangular brush for use alone or with the exten-
sion tubes (fig. 8).
- 120° curved lance for use alone or with the brushes.
- Long steam lance (fig. 9).
- Glass brush, to be used on its own or with extension hoses.
- If necessary, use the proper extension hoses. It is possible to
use a single extension hose.
Change the attachments only when all the switches on the
hand grip are off.
Do not change attachments while the appliance is emitting
steam, risk of burns.
Use only original attachments which offer optimum character-
istics of quality and safety. Failure to use original attachments
absolves the manufacturer from all liability.
Stopping the steam generator.
To stop the appliance, turn the steam phase, cleaning product
injection switches on the hand grip off (fig. 6); place the main
switch in the "O" position and unplug from the mains.
Turn the appliance on and off by means of the main switch only
and never by plugging in or unplugging the mains plug.
Never unplug by pulling the power cable.
IMPORTANT.
As with all technical appliances, your steam generator should
always be used according to the instructions.
Only maintenance authorised in this booklet may be carried out
by the user. All other operations are prohibited.
Before carrying out maintenance of any kind, unplug the steam
generator from the mains.
The appliance can only be disconnected from the mains by
unplugging it.
When maintenance has been completed, before reconnecting
the steam generator to the mains, check that the panels have
been replaced correctly and fixed using the screws provided.
Cleaning the appliance.
Do not use direct jets of water to clean the appliance. Use a
damp cloth only.
Clean all accessories thoroughly each time they are used.
- 13 -
!
!
!
MAINTENANCE
!