Operation Without The Remote Control Unit; Care And Cleaning - Technibel Climatisation MCA90MR5TA Serie Instrucciones De Uso

Up
Flap
Down
Air outlet
grille
Sweep function
The flap starts moving up and down to deliver air
over the sweep range.
• The flap automatically closes when the unit is off.
NOTES
• During the heating operation, the fan speed
will be very low and the flap will be in the
horizontal position (position 6 ) until the air
being blown out of the unit begins to warm.
Once the air warms up, the flap position and
fan speed change to the settings specified
with the remote control.
CAUTION
• Use the FLAP button on the remote control to adjust
the position of the flap. If you move the flap by hand,
the factual flap position and the flap position on the
remote control may no longer match. If this should
happen, shut off the unit, wait for the flap to close,
and then turn on the unit again; the flap position will
now be normal again.
• Do not have the flap pointed down during cooling
operation. Condensation may begin to form around the
air vent and drip down.
OPERATION WITHOUT THE REMOTE
CONTROL UNIT
If you have lost the remote control unit or it has troubles, follow
the steps below.
1. WHEN THE AIR CONDITIONER IS STOPPED
If you want to turn on the air conditioner push the button with a
pen to select the desired mode (COOL or HEAT).
NOTE
The air conditioner will start in automatic fan speed and flap
sweep operation. The temperature setting is 22°C for cooling
mode and 26°C for heating mode.
2. WHEN THE AIR CONDITIONER IS RUNNING
If you want to turn off the air conditioner push the button with a
pen until the OPERATION lamp is turned off.
NOTE
Power failure during operation.
In the event of power failure, the unit will stop. When the power
is resumed, the unit will restart automatically after 3 minutes.

CARE AND CLEANING

For safety, be sure to turn the air conditioner off and also to
disconnect the power before cleaning.
Do not pour water on the indoor unit to clean it. This will damage
the internal components and cause an electric shock hazard.
CASING AND GRILLE (INDOOR UNIT)
Clean the casing and grille of the indoor unit with a vacuum cleaner
brush, or wipe them with a clean, soft cloth.
If these parts are stained, use a clean cloth moistened with a mild
liquid detergent.
When cleaning the grille, be careful not to force the vanes out of
place.
The air intake grille can be removed in order to wash it
with water.
Removing and remounting the air intake grille
• With the air intake grille open all the way, grip both
arms with your hans and pull toward you to remove.
• To remount, hold the air intake grille roughly horizontal
and push it in until the arm shafts fit into the indenta-
tions in the main unit, then fit the grille into place.
Washing the grille with water
• Clean the grille gently using a soft sponge, or the like.
Then wipe away any remaining moisture.
• Neutral detergent may be used to remove stubborn
dirt. Then rinse thoroughly with water and wipe away
any remaining moisture.
Never use solvents, or harsh chemicals when cleaning the indoor
unit. Do not wipe the plastic casing using very hot water.
Some metal edges and the vanes are sharp and may cause
injury if handled improperly; be especially careful when you
clean these parts.
The internal coil and other components of the outdoor unit must
be cleaned every year. Consult your dealer or service centre.
AIR FILTER
The filter behind the air intake grille should be checked and cleaned
at least once every two weeks.
HOW TO REMOVE THE FILTER
Air intake grille
1. Move the flap on the air outlet grille to the vertical position with
Operation
the remote control unit.
selector
2. The filter is disengaged by pushing the tab up gently.
9
WARNING
CAUTION
Air filter
EG
Arm
Air intake grille