Saivod LV8 DIGITAL Manual De Uso Y Manutención página 14

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

Options
(Note: the various options must be selected before initiating the wash cycle)
• Delayed start
9
On the display, the delay period that was selected will be shown. The LED display will be blinking during the
entire delay period.
The selection of this setting option is confirmed when the number of the pre -selected programme appears
on the display.
• Half load
: when choosing this wash cycle option, the following indication will appear on the display:
10
(¯=wash superior basket,_=wash inferior basket). The corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre-selected programme appears
on the display.
• Pre-wash cancel
When pressing the button, the corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre-selected programme appears
on the display.
• Drying
: this programme option is carried out automatically by the programmes in whose cycle it is
12
included (see programme table). To modify the dryer setting, the drying button
initiating the chosen programme. On the display, the following information will appear: AO = no drying; A1=
Drying 20'; A2 = Drying 35'; A3 = Drying 45'.
The corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre -selected programme appears
on the display.
Note: In the models without the drying ventilator, this option is to be considered as waiting time at the end
of the cycle.
• Description of Start/Stop/Pause button
• It initiates the wash programme cycle
• When you turn on the machine, using the ON/OFF button, the display indicates the number of the last
program that has been carried out. In cases where the previous program has not yet finished, the display
will flash the number of this program. In order to re-start it you must simply press the "START" button
the remaining time that is necessary in order to finish the cycle will appear automatically on the display.
(Situations such as this will occur each time that you open the machine when it is carrying out a program).
• If pressed during the wash for less than 5" the machine will pause, the number of the program will be seen
flashing on the display, (in this case it is possible to add or remove dishes etc.)
In order to proceed with the washing program, close the door and press the button
• Programme settings by mistake (change programme)
• Reset by using the start/stop/pause button
produces a series of beeps).
• Repeat the select programme operation.
Note: If the programme has been initiated and has run beyond the water fill phase, the display indicates
"
", Then, the appliance will discharge all water, and (after a prolonged buzzer sound) the display will
indicate the pre-selected programme setting.
Now, the appliance is ready for a new setting.
Note: Once you have opened the door, always press the Start button
Activation / Elimination of the buzzer
b0 = Buzzer DEACTIVATED
b1 = Buzzer ACTIVATED
In order to access the setting of the BUZZER, keep the PROGRAM button
turn on the machine. The current setting "b1" will be visualised on the Display. In order to change this
setting, press the same button until you have selected the status of the buzzer that you desire. Wait for
approximately 6 seconds, without changing your choice, following this, the sound of the BUZZER will confirm
that the setting has been memorised.
End of cycle
Once the washing cycle is finished
is flashing wait for the end of the cycle.
Checking the functions
During the washing phase it is possible to visualise the various functions in the following manner:
By pressing the program selection button
display.
By pressing the half load button
By pressing the drying button
Stop
After the wash cycle, the dishwasher stops automatically, then unit will emit a long buzz to indicate the end of
the wahing cycle. To turn it off, press the button on/off
closed to insulate the appliance from the water supply system.
1 2 3 4 5 6 7 8 9 0
12
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
GB
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
: time delays for the initiation of the wash cycle can be set ranging from 1 to 16 hours.
11
: This option is only available for programmes that include a pre-wash.
(the buzzer sound indicates that the cycle has started).
7
14
, the program number will appear lit up and still on the display, if it
8
10
, the upper or lower washing area will be seen.
, the level of drying will be seen.
12
13
: keep the button pressed until the buzzer stops beeping (it
13
, the number of the pre-set program will be visualised on the
. After each wash cycle, the water faucet must be
7
must be pressed before
12
13
again.
13
in order to restart the dishwasher.
8
pressed down when you
,
13
Tabla de contenido
loading

Tabla de contenido