Tabla de contenido
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic
recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from
NAMCO EUROPE LIMITED.
While the information contained in this manual is given in good faith and was accurate at the time of printing.
NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
This machine has been manufactured in accordance with European Community Directives, and has been tested and complies with
the Directives 89/336/EEC and 72/23/EEC by the application of EN55014-1, EN55014-2 and EN60335-1 standards (see front of
manual) and as such bears the
Directives. Any unauthorised changes to this product, may contravene such Directives.
Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients,
some degradation of performance may occur. However the machine will recover normal performance once the source of the
interference has ceased or been removed.
Following abnormally high surges on the mains supply, the video monitor may need to be manualy reset by turning the machine OFF
and back ON.
Note:-
If the game processor resets due to an interuption or reduction of the mains voltage any credits established may be lost.
This game is not a machine as defined by the Machinery Directive 89/392/EEC
In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this
machine.
Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the
owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work.
In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.
This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to
the operating and service personnel at all times.
This machine is for indoor use only and should only be used for the purpose intended.
Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of this
machine.
The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its
WARNING
Warning denotes a hazard that could result in injury or death. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.
CAUTION
Caution denotes a hazard that could result in damage to the machine. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.
Only operate this machine after checking that it has been installed correctly and in accordance with the manual.
Parts of this machine move during game play, so there are places where the distance between the stationary
section and moveable section changes. There are warning notices to keep hands and feet clear of moving parts,
however if the operator feels that a person is in any danger, he should warn that person accordingly.
The warning notices must always be kept in good condition and replaced if worn, so that customers can read
them clearly.
If there is an error or problem with the machine, operation must be stopped immediately and the problem
rectified before any further use.
Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.
For continued protection against fire hazard, replace fuses with the same type and rating. The use of other fuses
or material is prohibited.
The power supply inside the monitor will remain hot and have areas of high voltage even though the machine
has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.
To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected
EARTHED plug.
If at any time the mains supply lead becomes damaged, it must be replaced immediately.
Do not turn the power switch ON until the machine has been installed correctly.
Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the
correct fuses are fitted.
marking. Any changes or modifications to this machine must be in accordance with the European
SAFETY WARNING
SAFETY NOTES
meaning before installing, servicing or making adjustments to this machine.
GENERAL SAFETY CONSIDERATIONS
Tabla de contenido
