Tabla de contenido
Idiomas disponibles
Idiomas disponibles
CAUTION
Improper treatment of pressure washer can
damage it and shorten its life.
• DO NOT insert any objects through cooling slots.
•
Use a damp cloth to wipe exterior surfaces clean.
•
Use a soft bristle brush to loosen caked on dirt, oil,
etc.
•
Use a vacuum cleaner to pick up loose dirt and debris.
•
Use low pressure air (not to exceed 25 psi) to blow
away dirt. Inspect cooling air slots and openings on
the pressure washer. These openings must be kept
clean and unobstructed.
Check and Clean Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is torn.
Check High Pressure Hose
High pressure hoses can develop leaks from wear,
kinking, or abuse. Inspect hose before each use.
Check for cuts, leaks, abrasions, bulging of cover, or
damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
WARNING
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury
and possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST exceed maximum
pressure rating of unit.
Check Gun and Nozzle Extension
Examine hose connection to spray gun and make sure
it is secure. Test trigger by pressing it and making
sure it springs back into place when you release it. Put
trigger lock in UP position and test trigger. You should
not be able to press trigger. Replace spray gun
immediately if it fails any of these tests.
Check In-Line Filter
Refer to the illustration and service the in-line filter if it
becomes clogged, as follows:
Nozzle Extension
1. Detach spray gun from high pressure hose.
Detach nozzle extension from spray gun and
remove o-ring and screen from nozzle extension.
Flush screen, spray gun, and nozzle extension
with clean water to clear debris.
2. Place in-line filter screen into threaded end of nozzle
3. Place o-ring into recess. Push o-ring snugly
4. Assemble nozzle extension to spray gun, as
Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
nozzle clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the nozzle following these instructions:
1. Shut off engine and turn off water supply.
2. Remove nozzle from end of nozzle extension.
3. Remove in-line filter from other end of nozzle
4. Use a small paper clip to free any foreign material
Use wire here
5. Using a garden hose, remove additional debris by
6. Reinstall nozzle and in-line filter into nozzle extension.
7. Reconnect nozzle extension to spray gun.
8. Reconnect water supply, turn on water, and start
9. Test pressure washer by operating with each
O–Ring Maintenance
Purchase an O–Ring Repair Kit at your local Sears or by
calling 1-800-366-PART or online at www.sears.com. It
is not included with the pressure washer. This kit
In-line Filter
includes replacement o-rings, rubber washer and water
inlet filter. Refer to the instruction sheet provided in the
kit to service your unit's o-rings.
O-ring
• NEVER repair leaking connections with sealant of any
16
extension. Direction does not matter. Push screen in
with eraser end of pencil until it rests flat at bottom
of opening. Take care to not bend screen.
against in-line filter screen.
described earlier in manual.
extension.
clogging or restricting nozzle.
to remove
debris.
back flushing water through nozzle extension.
Back flush between 30 to 60 seconds.
engine.
quick connect nozzle.
WARNING
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury
and possible amputation.
kind. Replace o-ring or seal.
Capítulos
Tabla de contenido
