Tabla de contenido
Idiomas disponibles
Idiomas disponibles
How to Use Selector Nozzle
The selector nozzle allows you to switch between five
different spray pattern nozzles. Spray patterns can be
changed while pressure washer is running once spray gun
trigger safety lock is engaged. The spray patterns vary as
shown below.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER change spray patterns without the trigger locked on the
spray gun.
• DO NOT twist selector nozzle while spraying.
Follow these instructions to change nozzle patterns:
1. Select desired spray pattern:
•
MAX - For stubborn or hard to reach surface such
as second story surfaces, paint removal, oil stains,
rust removal or other stubborn substances (tar,
gum, grease, wax, etc.).
•
GENERAL - For most all purpose cleaning such as
home siding, brick patios, wood decks, driveways
and sidewalks, garage floors, etc..
•
DELICATE - For gentle cleaning of cars/trucks,
boats, RV's, patio furniture, lawn equipment, etc..
•
FLUSH - For quick high flow clean up and long
reach cleaning of second story siding and windows.
•
SOAP - For general soap applications or to launch
soap to second story siding and windows.
2. Push button on selector nozzle, nozzle dial will pop up.
3. Turn dial until desired spray pattern lines up with button
on selector nozzle.
4. Push dial in until it locks into place.
Usage Tips
•
For most effective cleaning, keep selector nozzle from
8 to 24 inches (20 to 61 cm) away from cleaning surface.
•
If you get selector nozzle too close, especially using a
high pressure spray pattern nozzle, you may damage
surface being cleaned.
•
DO NOT get closer than 6 inches (15 cm) when cleaning
tires.
3100 PSI
2.5 GPM
3000 PSI
2700 PSI
2.6 GPM
2.8 GPM
2-IN-1 Soap System
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in death,
serious injury, and/or property damage.
• DO NOT use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps. Follow all
manufacturers instructions.
Cleaning and Applying Detergent with the
Project Pro® PerfectMix™ Siphon
To apply undiluted detergent using the blue
PerfectMix™ siphon, follow these steps:
1. Review use of selector nozzle.
2. Attach PerfectMix™ siphon hose to
pump and PerfectMix™ concentrate
bottle.
NOTICE Contact with the hot muffler could damage
detergent siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so as to keep it from inadvertently contacting the hot
muffler.
3. Make sure SOAP spray pattern nozzle is selected on
selector nozzle.
NOTICE Detergent cannot be applied with the MAX,
GENERAL, DELICATE or FLUSH spray pattern nozzles.
4. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE You must attach all hoses before you start the
engine.
• Starting the engine without all the hoses connected and without
the water turned ON could damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Start engine following instructions How to Start Your
Pressure Washer.
6. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
7. Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).
15
Capítulos
Tabla de contenido
