Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ENGINE TECHNICAL INFORMATION
This is a single cylinder, overhead valve (OHV), air
cooled engine. In the State of California, Model 120000
engines are certified by the California Air Resources
Board to meet emissions standards for 125 hours.
Such certification does not grant the purchaser, owner
or operator of this engine any additional warranties with
respect to the performance or operational life of this
engine. The engine is warranted solely according to the
product and emissions warranties stated elsewhere in
this manual.
Power Ratings
The gross power rating for individual gasoline engine
models is labeled in accordance with SAE (Society
of Automotive Engineers) code J1940 Small Engine
Power & Torque Rating Procedure, and is rated in
accordance with SAE J1995. Torque values are derived
at 2600 RPM for those engines with "rpm" called out
on the label and 3060 RPM for all others; horsepower
values are derived at 3600 RPM. The gross power
curves can be viewed at www.BRIGGSandSTRATTON.
COM. Net power values are taken with exhaust and
air cleaner installed whereas gross power values are
collected without these attachments. Actual gross
engine power will be higher than net engine power and
is affected by, among other things, ambient operating
conditions and engine-to-engine variability. Given the
wide array of products on which engines are placed,
the gasoline engine may not develop the rated gross
power when used in a given piece of power equipment.
This difference is due to a variety of factors including,
but not limited to, the variety of engine components (air
cleaner, exhaust, charging, cooling, carburetor, fuel
pump, etc.), application limitations, ambient operating
conditions (temperature, humidity, altitude), and
engine-to engine variability. Due to manufacturing and
capacity limitations, Briggs & Stratton may substitute an
engine of higher rated power for this engine.
SPECIFICATIONS
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
Max Outlet Pressure. . . . . . . . . . . . . . . . . . . . 3000 PSI*
Max Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 GPM
Detergent Mix . . . . . . . . . . . . . . . . . . . . Use as directed
Water Supply Temperature. . . . . . Not to exceed 100°F
Engine Specifications
Bore . . . . . . . . . . . . . . . . . . . . . . . . . 2.688 in. (68.28 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2.040 in. (51.82 mm)
Displacement . . . . . . . . . . . . . . . . . . . . . 11.58 in. (190 cc)
Spark Plug
Type: . . . . . . . . . . . . . . . . . . Briggs & Stratton 692051
Set Gap To: . . . . . . . . . . . . . . . . 0.020 inch (0.051 mm)
Armature Air Gap: . . . . . . 0.010-0.014 in.(0.25-0.36mm)
Valve clearance with valve springs installed and piston
1/4 in. (6 mm) past top dead center (check when engine
is cold).
Intake . . . . . . . . . . . . . . . . 0.004-0.008 in.(0.10-0.20 mm)
Exhaust . . . . . . . . . . . . . . . 0.004-0.008 in.(0.10-0.20 mm)
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 Quarts
Oil Capacity . . . . . . . . . . . . . . . . . . . 20 Ounces (0.6 liter)
NOTICE For practical operation, the engine load
should not exceed 85% of rated power. Engine power
will decrease 3-1/2% for each 1,000 ft. (300 m) above
sea level and 1% for each 10° F (5.6° C) above 77° F
(25° C). It should operate satisfactorily at an angle up
to 15°.
* This pressure washer is rated in accordance to
the Pressure Washer Manufacturers Association
(PWMA) standard PW101-2010 (Testing and Rating
Performance of Pressure Washers).
16
Capítulos
Tabla de contenido
