Specific Safety Rules - Black and Decker BDCMTI Manual De Instrucciones

14 • ENGLISH
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits,
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c. When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
7. Electrical safety
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
All manuals and user guides at all-guides.com
injury. If the power cord is replaced by an equally qualified
person, but not authorized by BLACK+DECKER, the
warranty will not be valid.
8. Labels on tool
V ........
A ........
FEATURES (Fig. A)
1. Impact Driver attachment
2. 1/4" hex quick-release chuck
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
provided with your Power Unit (BDCDMT112,
BDCDMT120, or BDEDMT) before using this attachment.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
f Hold power tool by insulated gripping surfaces,
f Wear ear protectors with impact drivers. Exposure
f Use clamps or another practical way to secure and
f When not in use, place tool on its side on a stable
f Keep your hair, clothing, and gloves away from air
The label on your tool may include the following
symbols:
Hz ....... Hertz
Read
Instructions
W ........ Watts
Manual
min ..... minutes
Use Eye
Protection
..... Alternating
Use Ear Current
Protection
..... Direct
Current
Use proper
n ....... No-Load
respiratory 0
Speed
protection
...... Class I
Volts
Construction
(grounded) Amperes
Not shown: Phillips head #2 screw bit
Warning! Read all safety warnings and all instructions.
Warning! Read all safety warnings and all instructions

SPECIFIC SAFETY RULES

when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Fastener contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
to noise can cause hearing loss.
support the work piece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
surface where it will not cause a tripping or falling
hazard. Some tools with large battery packs will stand
upright but may be easily knocked over.
vents. Air vents often cover moving parts in which
these items can be caught.
...... Class II
Construction
....... Earthing
Terminal
...... Safety Alert
Symbol
.../min Revolutions
or rpm or Recipro-
cation per
minute
BPM........ beats per
minute
IPM........ Impacts per
minute