Care And Maintenance - Chicco next2me Dream EVO Manual Del Usuario

configuration is allowed only with beds that allow compliancy
with all the conditions described in this paragraph.
In particular, the lowered side of the crib must always be posi-
tioned against the mattress of the parents' bed and the top of
the parents' mattress must be aligned with (or at most higher
than) the height of the open side of the crib (fig.18A-18B).More-
over, the crib must be fastened to the structure of the parents'
bed or to the mattress support (mesh or slat sprung base).
WARNING: Check that the structure of the crib in side sleeping
configuration does not interfere with the parents' bed.
WARNING: During use, make sure that the bedsheets, blan-
kets, etc. do not interfere with the crib's space.
WARNING: Check that the size of your bed is compatible with the
straps provided. If the straps are too short for proper installation, an
additional set of straps can be purchased and attached to the ones
that were provided with the product to lengthen them.
1. Lower the side of the crib by pushing button C3 and accom-
panying the side until it reaches the end of its travel (Fig.19).
WARNING: Use the crib with the side lowered only in side
sleeping mode.
2. Put the crib against the parents' bed and check its height
compared to the parents' mattress (Fig. 20).
WARNING: The top of the parents' mattress must be higher
than or the same as that of the side of the crib.If this is not the
case, use the adjustment system to achieve this condition on
both sides.
WARNING: In side sleeping configuration, the 2 feet of the crib
must be set at the same height.
3. To fasten the crib to the parents' bed (co-sleeping configura-
tion), use the included pair of straps D.
4. Carefully release the buckles C7 pushing slightly upwards
and then pulling them out (Fig. 21).
5. Fasten the grey buckles D2 to the buckles C7 located in the
rear part of the bottom of the crib C5 (Fig. 22).
6. Then fasten the red buckles D1 to the buckles C6 located in
the front part of the bottom of the crib C5 (Fig. 23).
7. Next, pass the straps around the parents' bed frame from top
to bottom (Fig. 24) and fasten the grey buckles D3 to form
a loop (Fig. 25). Make sure to repeat the step on both sides.
To make installation easy, when fastening the buckles, always
keep the crib slightly away from the parents' bed.
8. At this point put the crib against the parents' bed and tighten
the noose pulling the straps (fig.26). Carry out this step first
on one side and then on the other, adjusting the straps until
the crib is in contact with the parents' mattress.
WARNING: Before use, always make sure that there is no space
between the parents' mattress and crib' s side. Otherwise adjust the
straps pulling them until the required condition is restored. Make
sure that the side is always free to be lowered and raised completely.
9. Lock the crib's wheels. If fitting the feet of the crib under the
parents' bed while fastening the crib to the bed proves im-
possible, the bed can be fastened anyway by the following
the instructions above while also retracting the telescopic
feet A4 when setting the crib up against the bed. To activa-
teretraction, simply push the crib towards the bed so that
therelease buttons A3 (Fig. 27) are activated, retracting the
feetas much as necessary to install the crib correctly.
10. To close the side, simply lift it upwards, holding it from the
centre (Fig.28). Always make sure that it is engaged correctly.
WARNING: Whenever the side is lowered, make sure that the
position compared to the parents' mattress has not changed
from that illustrated in the paragraphs above.
WARNING: Use the product with beds and/or mattresses with
straight sides only. Do not use the product with round beds
and/or mattresses or water mattresses.
To be used with this product, the parents' bed must have a slat-
ted or mesh frame.
WARNING: When the product is used in co-sleeping configu-
ration (fastened to the bed), it must always be mounted on the
long side of the bed. DO NOT install the product at the head or
feet of the bed.

CARE AND MAINTENANCE

The crib and mattress have a resistant fabric lining that can be
removed completely and washed. To remove the fabric, follow
the instructions in the paragraph "REMOVING THE FABRIC. "
WARNING: Covering or removing the fabric may take a few
minutes and must be carried out by an adult.
Regularly inspect the product for signs of wear and damage.
In the case of damage, do not use and keep out of reach of
children.
When washing the fabrics pay close attention to the instruc-
tions on the label.
Do not use solvents, abrasive or overly aggressive products.
Machine washable at 30°C
30° C
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Check that the fabric and the stitching are in good condition
after each wash.
WARNING: When covering or removing the cover, take care
when handling the fabric parts to avoid accidental tears or
damage.
WARNING: The fabric part of the tilting side cannot be removed.
MAKING THE BED
The crib can be unfastened from the parents' bed when making
the bed. Just unfasten the grey buckles under the fabric lining.
When fastening the crib again to the parents' bed, pull the
straps again to make sure that the crib is correctly and secure-
ly fastened to the parents' bed. Make sure that all the steps il-
lustrated above in "Co-sleeping configuration (fastened to the
bed)" have been completed.
REMOVING THE COVER
1. Remove the mattress.
2. Release the fastening buttons C1.3.
3. To unfasten the frame C from the feet A, free the bottom part
by pulling the lever C2.2 outwards (Fig. 29) and the top part
by pressing the two buttons C2.1 located on either side (Fig.
30). Then pull upwards on the frame.
4. Open the 3 zippers C1.1 and C1.2 on the fabric.
5. You can now remove the fabric lining.
DISASSEMBLING THE CRIB
The crib can be disassembled completely to put it away in the
supplied bag. In order to complete the disassembly of the crib
after removing the fabric, remove the lower bar B, repeating
the steps illustrated in "ASSEMBLY OF THE CRIB" in reverse order.
WARRANTY
The product is guaranteed against any conformity defect in
normal conditions of use as described in the instructions.
The warranty shall not therefore apply in the case of damage
caused by improper use, wear or accidental events. For the du-
ration of the warranty on conformity defects please refer to the
specific provisions of applicable national laws in the country of
purchase, where appropriate.
16