Care And Maintenance - Chicco Next2me Dream Manual Del Usuario

you hear it click into place. Repeat the step on both sides.
6. Fasten the fabric lining "E" to the central structure "C"
fastening the 2 straps with clip "C2" on the lower part of the
lining (fig.7).
7. Fasten the buttons "C2" to the buttons "B5" to fasten the fabric
to the upper structure (fig.8) and complete by closing the
zippers E3 (fig.8A). Repeat the step for the missing side.
8. Position il mattress "F" on the bottom of the crib (fig.9).
9. Block the 4 wheels "A6" of the crib by lowering the levers that
activate the brakes (fig.10).
The crib is now ready to be used.
WARNING: Make sure that all the fasteners are engaged
correctly and that the zippers are closed and locked at the end.
WARNING: Do not use the crib with the articulated feet
partially or completely turned or released (fig. 11). The position
of correct use is illustrated in figure 12. In the case of accidental
knocking against the articulated feet, put them back in the
correct position by lifting the crib slightly.
WARNING: If the crib has been used previously in "Co-Sleeping
configuration (fastened to the bed), " make sure that the side is
in locked position and check that it is engaged correctly.
ADJUSTING THE CRIB HEIGHT
The crib can be adjusted at different heights. To adjust the
height, the setting button "A1" up and lift the crib to the desired
position (fig.13). Repeat the step on the opposite side.
The base of the crib can be slightly inclined by adjusting the 2
feet at different heights (fig.14).
WARNING: The crib can be inclined by a maximum of 4
positions between one foot and the other (e.g., right foot in
position 5 and left foot in position 1, see fig. 15).
WARNING: The child's head must always be positioned near
the raised end (fig.16).
WARNING: It is not possible to select different heights on the
two sides of the crib when in rocking configuration.
CO-SLEEPING CONFIGURATION (FASTENED TO THE BED)
It is possible to fasten the crib to the parents' bed (co-sleeping
configuration).
CAUTION - IMPORTANT FOR YOUR CHILD'S SAFETY: This
configuration is allowed only with beds that allow complying
with all the conditions described in this paragraph.
In particular, the side of the crib must always be positioned
against the mattress of the parents' bed and the parents'
mattress must be aligned with (or at most higher than) the
height of the crib's side (fig.17). Moreover, the crib must be
fastened to the frame of the parents' bed or to the mattress
support (mesh or slat sprung base).
WARNING: Check that the structure of the crib in co-sleeping
configuration does not interfere with the parents' bed.
WARNING: During use, make sure that the bedsheets, blankets,
etc. do not interfere with the crib's space.
1. Lower the side of the crib "B2" by gripping the relevant
interface "B4" and rotating it upward to release the side
lowering mechanism (fig.18).
WARNING: Use the crib with the bar lowered only in co-
sleeping configuration.
2. Put the crib against the parents' bed and check the height of
the crib compared to the parents' mattress.
WARNING: The height of the parents' mattress must be higher
than or the same as that of the side of the crib. If this is not the
case, use the adjustment system to achieve this condition on
both sides.
WARNING: In co-sleeping configuration, the 2 feet of the crib
must be set at the same height.
3. To fasten the crib to the parents' bed (co-sleeping
configuration), use the pair of supplied straps "D". The straps
are found in the lower pocket "E2" of the fabric lining (fig.19).
4. Fasten the grey buckles "C3" under the fabric lining on both
sides. Make sure the red buckle "D1" is positioned above the
strap as illustrated in figure 20.
5. Then run the strap around the structure of the parents'
bed from the bottom up (fig.21) and fasten the red buckle
forming a noose (fig.22). Repeat this operation on the other
side. To make installation easy, when fastening the buckles,
always keep the crib slightly away from the parents' bed.
6. At this point put the crib against the parents' bed and tighten
the noose pulling the straps (fig.23). Carry out this step first
on one side and then on the other, adjusting the straps until
the crib is in contact with the parents' mattress.
WARNING: Before use, always make sure that there is no space
between the parents' mattress and crib's side. Otherwise adjust
the straps pulling them until the required condition is restored.
Make sure that the side is always free to be lowered and raised
completely.
7. Fit the length of the straps in excess inside the pocket on the
bottom of the fabric lining.
8. Lock the crib's wheels.
If when fastening the crib to the parents' bed it is not possible to
fit the crib's feet under the parents' bed, the bed can be fastened
anyway by the following the instructions above and rotating the
articulated feet when putting the crib against the bed.
To turn the feet, pull the rotation release button "A4" and turn
the feet "A5" of the crib inward by hand (fig.24).
9. To close the side that can be lowered, just pull up by holding
it by the upper mobile structure "B2" (fig.25). Always make
sure that it is engaged correctly.
WARNING: Whenever the side is lowered, make sure that the
position compared to the parents' mattress has not changed
from that illustrated in the paragraphs above.
WARNING: Never use the rocking function when the crib is in
"Co-Sleeping configuration (fastened to the bed). "
WARNING: Use the product with beds and/or mattresses with
straight sides only. Do not use the product with round beds
and/or mattresses or water mattresses.
WARNING: When the product is used in "Co-Sleeping
configuration (fastened to the bed), " it must always be mounted
on the long side of the bed. DO NOT install the product at the
head or feet of the bed.

CARE AND MAINTENANCE

The crib and mattress have a resistant fabric lining that can be
removed completely and washed.
To remove the fabric, follow the instructions in the paragraph
"HOW TO REMOVE THE FABRIC COVER. "
WARNING: Covering or removing the fabric may take a few
minutes and must be carried out by an adult.
Regularly inspect the toy for signs of wear and any damage.
In the case of damage do not use and keep out of reach of
children.
When washing the fabrics pay close attention to the
instructions on the label.
Do not use solvents, abrasive or overly aggressive products.
Wash by hand in cold water
Do not bleach
30° C
Do not tumble dry
Do not iron
Do not dry clean
Check that the fabric and the stitching are in good condition
12 after each wash.