BFT SIRIO CBA 230 INV Manual De Instalación página 14

Logic Definition
HOLD-TO-RUN Deadman
Block pulses during
IBL OPEN
opening
Block pulses during
|IBL TCA
TCA
Block pulses during
IBL CLOSE
closing
OPEN IN OTHER
Open in other
direction
DIRECT.
Configuration of
SAFE 1 safety input SAFE 1.
72
Configuration of
SAFE 2 safety input SAFE 2.
74
Configuration of
SAFE 3 safety input SAFE 3.
77
Configuration of
IC 1 command input IC 1.
61
Configuration of
IC 2 command input IC 2.
62
Configuration of
command input IC 3.
IC 3
64
Configuration of
IC 4 command input IC 4.
65
Configuration of
AUX 3 AUX 3 output.
26-37
FIXED CODE Fixed code
14 -
SIRIO CBA 230 INV
All manuals and user guides at all-guides.com
INSTALLATION MANUAL
Cross out
Default setting
used
0 Pulse operation.
Deadman mode.
Input 61 is configured as OPEN UP.
Input 62 is configured as CLOSE UP.
1
Operation continues as long as the OPEN UP or CLOSE UP keys are held down.
WARNING: safety devices are not enabled.
0
Emergency Deadman mode. Usually pulse operation.
If the board fails the safety device tests (photocell or safety edge, Er0x) 3 times in a row, the device is
switched to Deadman mode, which will stay active until the OPEN UP or CLOSE UP keys are released.
2 Input 61 is configured as OPEN UP.
Input 62 is configured as CLOSE UP.
WARNING: with the device set to Emergency Deadman mode, safety devices are not enabled.
0 Pulse from inputs configured as Start E, Start I, Ped has effect during opening.
0
1 Pulse from inputs configured as Start E, Start I, Ped has no effect during opening.
0 Pulse from inputs configured as Start E, Start I, Ped has effect during TCA pause.
0
1 Pulse from inputs configured as Start E, Start I, Ped has no effect during TCA pause.
0 Pulse from inputs configured as Start E, Start I, Ped has effect during closing.
0
1 Pulse from inputs configured as Start E, Start I, Ped has no effect during closing.
0 Standard operating mode (Fig.G Rif. 1).
0
1 Opens in other direction to standard operating mode (Fig. G Rif.2)
0 Input configured as Phot (photocell).
0 1 Input configured as Phot test (tested photocell).
2 Input configured as Phot op (photocell active during opening only).
3 Input configured as Phot op test (tested photocell active during opening only).
6 4 Input configured as Phot cl (photocell active during closing only).
5 Input configured as Phot cl test (tested photocell active during closing only).
6 Input configured as Bar, safety edge.
2 7 Input configured as Bar, tested safety edge.
8 Input configured as Bar 8k2 (Not active on SAFE 3).
0 Input configured as Start E.
0
1 Input configured as Start I.
2 Input configured as Open.
4
3 Input configured as Close.
4 Input configured as Ped.
2
5 Input configured as Timer.
3 6 Input configured as Timer Pedestrian.
0 Output configured as 2nd Radio Channel.
1 Output configured as SCA (gate open light).
2 Output configured as Courtesy Light command.
0 3 Output configured as Zone Light command.
4 Output configured as Stair Light
5 Output configured as Alarm
6 Output configured as Flashing light
Receiver is configured for operation in rolling-code mode.
0
Fixed-Code Clones are not accepted.
0
Receiver is configured for operation in fixed-code mode.
1
Fixed-Code Clones are accepted.
Optional extras