Grohe Europlus E 36 021 Manual Del Usuario página 8

Cleaning mode
Cleaning mode is activated when the hand is held for 5 s at
a distance of 3 - 7cm in front of the sensor system (indicator
lamp flashes). Water flow is interrupted for 3 minutes.
When a user enters the detection zone again for 5 s or after
the time has elapsed, the water flow is initiated again.
Automatic safety shut-off
After 60 s (factory setting) of continuous detection of an object,
the infrared electronics automatically stop the water flow.
The automatic safety shut-off can be set in steps of 5 - 420 s
using the remote control (see Special accessory,
Prod. no.: 36 206).
Changing type of detection
The type of detection can be changed using the remote control
(see Special accessory, Prod. no.: 36 206).
Stop water flow only when the sensor system is
approached with the hands (3 - 7cm).
- Press the button
detection zone is reached (sensor system indicator lamp
flashes 2 x long).
- When the button is pressed again,
detection is switched to operation only via approaching of
the sensor system with the hand (sensor system indicator
lamp flashes 5 x long and 3 x short).
Start / stop of the water flow only when a person enters
and moves out of the detection zone (> 35cm).
- Press the button
detection zone is reached (sensor system indicator lamp
flashes 2 x long).
- When the button is pressed again
is switched to operation only via person entering and moving
out of the detection zone (sensor system indicator lamp
flashes 5 x long and 3 x short).
The detection range can be set using the
buttons.
Automatic flushing (factory setting: deactivated)
The automatic flushing serves to maintain water hygiene in the
case of long-term non-utilisation of the fitting and activates
water flow for 1 – 10 minutes, 1 - 3 days after the last use.
Safety note:
Ensure free draining in the case of activated
automatic flushing.
5
repeatedly until the minimum
the type of
repeatedly until the maximum
the type of detection
and
The automatic flushing can be set using the remote control
(see Special accessory, Prod. no.: 36 206) as follows:
1. Switch automatic flushing on / off
• Press and hold the RESET button.
• Then additionally press OFF AUTO button within 2 s.
(indicator lamp in the sensor system of the fitting flashes).
- Switching on: Within 10 s, press OFF AUTO button
Warning lamp in sensor system flashes 4 x short = On
- Switching off: Within 10 s, press OFF AUTO button
Warning lamp in sensor system flashes 2 x long = Off
Setting mode is quit automatically after 10 s.
2. Set flush interval to 3 days or 1 day
• Press the TEST button => test mode is switched on
The flushing interval can be set via the ON AUTO button.
• Press the ON AUTO button as required.
The indicator lamp in the sensor system of the fitting flashes:
- 2 x long = 1 day flush interval is set
- 4 x short = 3 day flush interval is set
Setting mode is quit by pressing the TEST button,
or automatically after 60 sec.
3. Set flushing duration in minute intervals
from 1 to 10 minutes
• Press the TEST button => test mode is switched on
Using the + and - buttons (
duration can be increased (+) or reduced (-).
• Press the + or - button (
The indicator lamp in the sensor system of the fitting flashes:
- 4 x short = adjustment by one step (approx. 1 minute)
- 2 x long = end position has been reached.
Setting mode is quit by pressing the TEST button, or
automatically after 60 sec.
Setting continuous running time to 3.5 min
or 11 min
(factory setting: 3.5 min)
• Press the TEST button => test mode is switched on
The continuous running time can be set using the
OFF AUTO button.
• Press the OFF AUTO button as required.
The indicator lamp in the sensor system of the fitting flashes:
- 2 x long = 11 min continuous running is set
- 4 x short = 3.5 min continuous running is set
Setting mode is quit by pressing the TEST button,
or automatically after 60 sec.
button), the flushing
button).