Tabla de contenido
Idiomas disponibles
Idiomas disponibles
TROUBLE
Unit Will Not Start or
Unit Stops
Cutting Attachment Will Not Turn
When Trigger is Squeezed
Cutting Attachment Will Not
Advance Line|
Cutting Line Advances
Uncontrollably
MOTOR
Motor Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Volt Electric
Operating RPM (both lines fully extended)
Low Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,000-5,500 rpm
High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6,000-7,000 rpm
Amperage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 Amps
Ignition Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Momentary Trigger Switch
DRIVE SHAFT AND CUTTING ATTACHMENT
Drive Shaft Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Steel Tube, Coupler
Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Optional
Cutting Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RapidRewind Head
Line Spool Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 in. (102 mm)
Trimming Line Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.080 in. (2.03 mm)
Cutting Path Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 in. (381 mm)
Operating Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Approx. 10.0 lbs. (4.54 kg)
TROUBLESHOOTING CHART
CAUSE
Unit unplugged
Cutting attachment bound with grass or
debris
Cutting Attachment out of line
Reel bound up
Cutting attachment dirty
Indexing teeth worn or burred
Line welded
Line twisted when refilled
Not enough line exposed
Oil in cutting attachment
SPECIFICATIONS
– 15 –
REMEDY
Check cord to see if it is plugged
into an electrical outlet
Stop unit and clean cutting
attachment
Refill cutting line
Replace reel
Clean cutting head reel and reel
housing
Replace reel and reel housing
Disassemble, remove the welded
section, and rewind the line
Disassemble cutting attachment
and rewind the reel
Push the Bump Knob and pull
out the line until a minimum of
4 inches (102mm ) is outside of
cutting attachment
Clean cutting attachment
Capítulos
Tabla de contenido
Solución de problemas
