UFESA PV1530 Instrucciones De Uso página 8

When the steam iron has reached the desired temperature
(flashing icon ▲ will disappear), start steaming by setting the
steam regulator to «MAX» and by repeatedly pressing the
steam button
When using the steam function for the first time, do not apply
it on the laundry, as there could still be dirt in the steam
dispenser.
Your new iron may smell and give off some smoke when
you use it for the first time, this is normal and will cease
after a short while.
HOW TO USE THE IRON
«▲» icon blinks while the iron is in process of heating up, and
dissapears as soon as the desired temperature is reached.
Now you can start ironing
«▼» icon blinks while the iron is in process of cooling down,
and dissapears as soon as the desired temperature is reached
(it could take several minutes to go from a higher temperature
to a lower one)
Check the laundry care label for the required ironing
temperature. If you do not know what kind or kinds of fabric
an article is made of, determine the right ironing temperature
by ironing a part that will not be visible when you wear or use
the article.
Start ironing the articles that require the lowest ironing
temperature, such as those made of synthetic fibres.
Silk, woollen or synthetic materials: iron the reverse side of the
fabric to prevent shiny patches. Avoid using the spray function
to prevent stains.
FILLING THE WATER TANK
Set the steam regulator to the
unplug the iron from the mains!
Use only clean water from the tap without mixing anything with
it. The addition of other liquids, such as perfume, will damage
the appliance.
Do not use condensation water from tumble dryers, air
conditionings or similar. This appliance has been designed to
use normal tap water.
To prolong the optimum steam function, mix tap water with
distilled water 1:1. If the tap water in your district is very hard,
mix tap water with distilled water 1:2.
Never fill beyond the «MAX» water level mark.
GETTING READY
Remove any label or protective cover from the soleplate.
Wait for the iron to reach the desired temperature (flashing
icon ▲ or ▼ will disappear)
IRONING WITHOUT STEAM
IRONING WITH STEAM
Only when the temperature on the display is placed in the
areas with the steam symbol
SPRAY
Do not use the spray function with silk.
SHOT OF STEAM
Set the temperature in the «MAX LINEN
Interval between shots of steam should be 5 sec.
VERTICAL STEAM
Do not iron clothing while it is being worn!
Never direct the steam at persons or animals!
Interval between shots should be 5 sec.
Wait 10 sec. after a cycle of 4 shot.
MULTIPLE DESCALING SYSTEM
Depending on the model, this range is equipped with
the «Aquacalc2» (=component 1 + 2) or «Aquacalc3»
(=component 1 + 2 + 3) descaling system.
1. Self-clean
Each time you use the steam regulator, the «self-clean» system
cleans the mechanism of scale deposits.
2. Función Calc
The «Función Calc» function helps to remove scale particles
out of the steam chamber. Use this function approximately
every 2 weeks, if the water in your area is very hard.
Fill the water tank, plug in the iron and set the temperature to
the «MAX LINEN
After the necessary warm-up period, unplug the iron and hold
it over a sink. Press «Función Calc» button and gently shake the
iron. Boiling water and steam will come out, carrying scale or
deposits that might be there. When the iron stops dripping,
release the button, plug the iron in and heat it up again until
1 the remaining water has evaporated.
3. Anti-calc
position and
The «anti-calc» cartridge has been designed to reduce the
build-up of scale produced during steam ironing, helping
to extend the useful life of your iron. Nevertheless the «anti-
calc» cartridge cannot remove all of the scale that is produced
naturally over time.
AUTO SHUT-OFF FUNCTION
The auto shut-off function switches off the iron when it is left
unattended, thus increasing security and saving energy. After
plugging in the appliance, this function will be inactive for the
first 2 minutes in order to give the appliance time to reach the
set temperature.
After this time, if the iron is not moved for 8 minutes while
in the upright position or 30 seconds while resting on its
soleplate or on its side, then the safety circuit will switch the
appliance off automatically and display´s light and icon
will start flashing.
To reconnect the iron, just move it about gently.
2
ANTI-DRIP SYSTEM
If the temperature is set too low, the steam is automatically
3
switched off to avoid dripping.
STORING
Turn the steam regulator to position
4
». position.
5 CLE
ADV
6
dispo
7
poin
distri
refus
appl
pena
that t
the e
to b
dispo
shop
impo
and
syste
Your
abou
Pro
The
Disp
show
The
8
Wat
stea
Stea
Spra
9
Wat
sole
the
10
Smo
con
time