Skil 0731 Manual Original página 9

Line trimmer
INTRODUCTION
• This tool is intended for the cutting of grass and weeds
under bushes as well as on slopes and edges that can
not be reached with a lawn mower
• This tool is not intended for professional use
• Check whether the packaging contains all parts as
illustrated in drawing 9
• When parts are missing or damaged, please contact your
dealer
• Read this instruction manual carefully before use
and save it for future reference 2
• Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious injury
TECHNICAL DATA 1
TOOL ELEMENTS 0
A Guide handle
B Knob for adjusting guide handle
C Cutting guard
D Cord restraint
E Lower tube
F Unlocking button
G Trigger switch
H Flower guard
J Line cutting blade
k Spool cap
L Ventilation slots
M Storage rail (screws not supplied)
N Storage hook
SAFETY
SPECIFIC SAFETY INSTRUCTIONS FOR LINE
TRIMMERS
GENERAL
• Be familiar with the controls and the proper use of the tool
• The user is responsible for accidents or hazards
occurring to other people or their property
• Only use the tool when the ambient temperature is
between 0°C and 40°C
• Never mount metal cutting elements onto this tool
PERSONAL SAFETY
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety
• Ensure that children do not play with the tool
• Never allow children or people who are not familiar with
the operating instructions to use the tool
• Keep your fingers away from the line cutting blade
integrated in the cutting guard
• Keep hands and feet away from the cutting lines while
trimming, especially when switching on the tool
• Always wear eye protection, long trousers and sturdy
0731
shoes when operating the tool
• Never operate the tool in the direct vicinity of persons;
stop using the tool when persons (especially children) or
pets are nearby
• Never operate the tool when you are tired, sick or under
the influence of alcohol or other drugs
ELECTRICAL SAFETY
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• Inspect the cord periodically and have it replaced by a
qualified person, if damaged
• Inspect the extension cord periodically and replace it, if
damaged (inadequate extension cords can be
dangerous)
• Only use an extension cord which is intended for outdoor
use and equipped with a watertight plug and coupling-
socket
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• When operating the tool use a residual current device
(RCD) with a triggering current of 30 mA maximum
• Do not run over, crush or pull the (extension) cord
• Protect the (extension) cord from heat, oil and sharp
edges
• Keep the (extension) cord away from the rotating
cutting lines
• Always switch off tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
BEFORE USE
• Only use the tool in daylight or with appropriate artificial
lighting
• Check the functioning of the tool before each use and
after any impact; in case of a defect, have it repaired
immediately by a qualified person (never open the tool
yourself)
• Before use, thoroughly inspect the cutting area and
remove any object that the tool may sling during cutting
(such as stones, loose pieces of wood, etc.)
DURING USE
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• Never operate the tool with a damaged cutting guard or
without the cutting guard mounted
• The cutting lines continue to rotate for a short time
after the tool is switched off
• Do not cut grass which is not on the ground (e.g. on walls
or rocks)
• Do not cross roads or gravel paths with the tool still
running
• Do not get distracted and always concentrate on what
you are doing
• Always disconnect plug from power source
- whenever leaving the tool unattended
- before clearing jammed material
- before checking, cleaning or working on the tool
9