Safety Equipment; Pressure Switch; Appliance Switch; Motor Protection Circuit Breaker - Parkside PDR 12 A1 Traducción Del Manual De Instrucciones Original

CAUTION!
Never fill the water tank with solvents, liquids
►
containing solvents, or undiluted acids (e .g .
cleaning agents, petrol, paint thinner, acetone) .
They could damage the materials used in the
appliance .
Do not leave the appliance unattended while
►
it is in operation .
Do not leave the appliance unattended while
►
it is connected to the power supply .
Place the appliance on a firm, level surface to
►
ensure stability .
CAUTION!
Do not operate the appliance at temperatures
►
below 0°C .

Safety equipment

CAUTION
Do not change or bypass the safety functions of
►
the appliance . They are there for your safety .
The safety equipment is designed to protect the user and may not be
deactivated or repurposed .

Pressure switch

The pressure switch activates the low-pressure spray jet . When you let go
of the trigger, the low-pressure spray jet stops .

Appliance switch

The appliance switch prevents the appliance from being switched on
unintentionally .

Motor protection circuit breaker

The appliance switches off automatically when the power consumption
becomes too high .

Before use

Operating the appliance on a 12 V circuit

WARNING!
► The current tolerance of your vehicle's wiring system must be
compatible with the connected appliance .
► Refer to your vehicle handbook (cigarette lighter) .
♦ Remove the charging socket cover
♦ Connect the correct end of the 12 V cable
on the appliance .
♦ Connect the 12 V connector plug
usually the cigarette lighter socket on the dashboard of your vehicle .
Many vehicles have a second socket by the rear seats or in the boot .
The red LED on the 12 V connector plug
PDR 12 A1
.
to the 12 V socket
with a suitable socket . This is
10a
lights up .
10a
♦ You can now run the appliance on the 12 V socket . Please note that
this does not charge the battery .
♦ Disconnect the 12 V connector plug
when you are finished using the appliance .
♦ Remove the 12 V cable from the 12 V socket
♦ Close the 12 V socket again by replacing the charging socket
cover .

Charging the appliance with the mains adapter

NOTE
► While the battery is charging, the status LED
► When the battery is fully charged, the status LED
► It takes approximately 1 hour for the battery to charge fully when
empty .
♦ Remove the charging socket cover
♦ Connect the end of the charger cable
mains adapter .
5a
♦ Plug the mains adapter into a mains power outlet .
♦ Disconnect the mains adapter
charging socket of the mains adapter
charged .
♦ Replace the charging socket cover

Filling the water tank

towards the Open mark until you can pull the
♦ Turn the water tank
water tank off the base
create suitable counter-pressure .
♦ Open the lid of the water tank
with water . Do not fill the tank beyond the 5 l mark .
NOTE
► The water tank has a capacity of 5 litres .
► Fill the water tank with fresh water only .
► Do not open the lid during operation .
♦ Close the lid of the water tank
♦ Put the water tank back on the base
towards the Close mark on the base
Hold the base firmly with one hand to create suitable counter-pressure .
Ensure that the I mark on the base
water tank when it has clicked into place .

Operation

Switching the appliance on

CAUTION!
► If the pump runs for 2 minutes without drawing in liquid, it will run dry
and the appliance will be damaged .
♦ Press the On/Off switch to switch the appliance on . The status
LED lights up green . The pump builds up pressure .

Turning the appliance off

♦ Press the On/Off switch again to switch the appliance off .
The status LED goes out .
from the cigarette lighter socket
10a
.
lights up red .
lights up green .
.
to the charging socket on the
from the mains power outlet and the
as soon as the battery is fully
5a
to close the charging socket .
. Hold the base firmly with one hand to
. Use a tap to fill the water tank
.
. Turn the water tank
until it clicks into place .
is aligned with the I mark on the
│
GB│IE 13 ■