Bosch PWR 180 CE Manual Original página 24

Technical Data
Wall processing system
Article number
Handpiece
Rated power input
Rated speed
Max. outer diameter of application
tool
Thread of sander spindle
Thread length (max.) of sander
spindle
Reduced starting current
Constant electronic control
Speed preselection
Soft starting
Restarting Protection
Overload Protection
Weight according to
EPTA-Procedure 01/2003
Protection class
Dust container (Accessory)
Filter system
Container volume
Weight according to
EPTA-Procedure 01/2003
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 91 dB(A); Sound power level
102 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =7.5 m/s , K=1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Bosch Power Tools
PWR 180 CE
3 603 CC4 0..
W 1010
-1
min 410–1650
mm 180
M 14
mm 22






kg 3.6
/II
Membrane
filter
l 3
kg 2.5
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-3.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 05.06.2014
Assembly
 Before any work on the machine itself, pull the mains
plug.
Mounting application tools
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessory can lead to injuries.
Different application tools are available depending on the ma-
terial to be worked and the desired material removal rate on
the surface.
An overview of the right choice of application tool for an appli-
cation together with a speed recommendation can be found in
section "Selection of the Application Tool and Speed Setting",
page 28.
Note: Do not put the handpiece 1 down without an applica-
tion tool mounted on it (sanding plate, wire brush, perforator,
cup wheel, backing pad, etc.). The brush collar 12 may be-
come bent and damaged as a result.
Changing the Sanding Sheets
The surface of the sanding plate 36 is fitted with Velcro back-
ing for quick and easy fastening of sanding sheets with Velcro
adhesion.
– When attaching a new sanding sheet, remove any dust or
debris from the sanding plate 36, e. g., with a brush.
– Position the sanding sheet 37 flush to the edge of the sand-
ing plate 36, then place the sanding sheet on the sanding
plate and press it on firmly.
– To remove the sanding sheet 37, lift it from the side and
pull it off of the sanding plate 36.
English | 25
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
2 609 007 769 | (2.6.14)