SICK WTF18-3 Manual De Operación página 53

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 40
67
故障诊断
67
故障诊断
68
表故障诊断
52
WT18-3A600S02:开关距离为 100 mm / 90%,开关频率为 1000 Hz,输出信号
开关装置:推拉式输出 Q: PNP: 光控; NPN: 暗控, Pin 1: L+, Pin 2: M, Pin 3: 未连
接, Pin 4: 未连接, Pin 5: Q, Pin 6: 未连接
表 I 中罗列了传感器无法执行某项功能时应采取的各项措施。
LED 指示灯 / 故障界面 /
LED indicator/fault pattern
绿色 LED 未亮起 /
Green LED does not light up
绿色 LED 未亮起 /
Green LED does not light up
绿色 LED 未亮起 /
Green LED does not light up
当 Health 存在且随后观察到
输出信号时当 Alarm 存在且
随后观察到输出信号时,黄色
LED 闪烁 /
Yellow LED flashes; if Health
is present then take note of
the corresponding output
signal; if Alarm is present
then take note of the corre‐
sponding output signal
黄色 LED 闪烁(非常短
暂) /
Yellow LED flashes (only
briefly)
黄色 LED 亮起,光路中无物
体 /
Yellow LED lights up, no ob‐
ject in the path of the beam
原因 /
Cause
无电压或电压低于极限值 /
No voltage or voltage be‐
low the limit values
电压中断 /
Voltage interruptions
传感器损坏 /
Sensor is faulty
尽管传感器准备就绪,但运
行条件不佳 / 此外在 Health-
输出端: 切断了电源 /
Sensor is still ready for ope‐
ration, but the operating
conditions are not ideal/
additionally with health out‐
put: power supply interrup‐
ted
示教模式 /
Teach-in mode
传感器和背景之间的间距过
小 /
/ Distance between the
sensor and the background
is too short
措施 /
Measures
检查电源,检查整体电气连
接(导线和插头连接) /
Check the power supply,
check all electrical connec‐
tions (cables and plug con‐
nections)
确保电源稳定无中断 /
Ensure there is a stable
power supply without inter‐
ruptions
如果电源正常,则更换传感
器 /
If the power supply is OK,
replace the sensor
检查运行条件: 光束(光
斑)完全对准物体 / 清洁光
学表面 / 重新设置灵敏度
(电位计)(示教) / 检查
开关距离,必要时调整;参
见图 F. / Health 输出端:检
查电源,检查整体电气连接
(电缆和插头连接) /
Check the operating condi‐
tions: Fully align the beam
of light (light spot) with the
object. / Clean the optical
surfaces . / Readjust the
sensitivity (potentiometer)
(teach-in) / Check sensing
range and adjust if neces‐
sary; see graphic F. / With
health output: Check the
power supply, check all
electrical connections (ca‐
bles and plug connections).
检查示教模式 /
Check the teach-in mode
降低开关距离,参见图 F /
Reduce the sensing range,
see graphic F
8010586.YM42 | SICK
Subject to change without notice
Tabla de contenido
loading

Este manual también es adecuado para:

Wt18-3

Tabla de contenido