Ryobi EID-500RE Manual De Utilización página 9

GB
F D
THANK YOU FOR BUYING A RYOBI PRODUCT
To ensure your safety and satisfaction, carefully read
through this OWNER'S MANUAL and the SAFETY
INSTRUCTIONS before using the product.
INSTRUCTIONS FOR SAFE HANDLING
Make sure that the tool is only connected to the voltage
■
marked on the name plate.
Never use the tool if its cover or any bolts are missing.
■ If the cover or bolts have been removed, replace them
prior to use. Maintain all parts in good working order.
Always secure tools when working in elevated positions.
■
Never touch the blade, drill bit, grinding wheel or
■
other moving parts during use.
Never start a tool when its rotating component is
■
in contact with the work piece.
Never lay a tool down before its moving parts have
■
come to a complete stop.
ACCESSORIES: The use of accessories or attachments
■
other than those recommended in this manual might
present a hazard.
REPLACEMENT PARTS: When servicing use only
■
identical replacement parts.
WARNING: When using electric tools, basic safety
■
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock and
personal injury.
Keep work area clean. Cluttered areas and benches
■
invite injuries.
Consider work area environment. Do not expose
■
power tools to rain. Do not use power tools in damp
or wet locations. Keep work area lit. Do not use
power tools where there is risk of fire or shock
Guard against electric shock. Avoid body contact with
■
earthed or grounded surface (e.g. pipes, radiators,
ranges, refrigerators).
Keep children away. Do not let visitors touch
■
the tool or extension cord. All visitors should be kept
from area.
Store idle tools. When not it use, tools should be stored
■
in a dry, high or locked up place, out of reach of children
Do not force the tool. It will do the job better and safer
■
at the rate for which it was intended.
Use the right tool. Do not force small tools or
■ attachments to do the job of a heavy duty tool.
Do not use tool for purposes not intended.
Use safety glasses. Also use face or dust mask if
■
the cutting operation is dusty.
E I P NL S DK N FIN GR
English
Do not abuse the cord. Never carry the tool by the cord
■
or yank it to disconnect it from the socket. Keep the cord
away from heat, oil and sharp edges.
Do not overreach. Keep proper footing and balance
■
at all times.
Maintain tool with care. Keep cutting tools sharp
■
and clean for better and safer performance. Follow
instructions for lubrication and changing accessories.
Inspect tool cord periodically and if damaged have
it repaired by an authorized service facility. Inspect
extension cords periodically and replace if damaged.
Keep handles dry, clean and free from oil and grease
Disconnect tools when not in use, before servicing
■
and when changing accessories such as blades,
bits and cutters.
Avoid unintentional starting. Do not carry a plugged-in
■
tool with a finger on the switch. Ensure that the machine
is switched off before connecting to the power supply.
When tool is used outdoors, use only extension cords
■
intended for outdoor use.
Stay alert. Watch what you are doing. Use common
■
sense. Do not operate tool when you are tired.
Check for damaged parts. Before further use of the
■
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment, breakage of parts, mounting and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired
or replaced by an authorized service centre unless
otherwise indicated in this instruction manual.
Have defective parts replaced by an authorized
service facility. Do not use the tool if the switch does
not turn it on and off.
Make sure that the drill bit is securely mounted.
■
An incorrectly mounted bit is extremely dangerous
since it can fly off or break during drilling.
Dress properly. Do not wear loose clothing or jewellery,
■
they can be caught in moving parts. Protective gloves
and non-skid footwear are recommended when
working outdoors. Wear protective hair covering
to contain long hair.
Hold the tool securely with both hands. If not held
■
securely, accidents or injury may result.
Never touch the chuck or metal body parts when
■
drilling walls, floors, or other surfaces covering
electrical wiring. Hold the tool only by the plastic
handle to prevent electric shocks.
While operating, the work piece must be securely
■
held with a vice or clamp to prevent it from moving
due to the drill rotation.
5
H CZ RUS RO PL SLO HR TR