Kenwood ES430 Serie Manual Del Usuario página 6

to make espresso using ground coffee
1 Pre heat the appliance as described on page 2.
2 Check that there is water in the tank.
3 Select the desired filter and fit into the filter holder. Make sure that the tab on
the filter fits into the slot on the filter holder.
Use the smaller filter for making one cup of coffee (or when using coffee pods)
●
and the larger filter for 2 cups.
4 Add the coffee using the measuring spoon provided one level spoon per cup,
level the surface then lightly press with the back of the measuring spoon. Wipe
off any coffee around the rim.
● When buying ground coffee make sure it is suitable for espresso machines.
● Never press the coffee too firmly as the coffee will come out slowly and the
crema will be of a dark colour. However, if it is pressed too lightly, the coffee will
come out too fast and the crema will be a light colour.
5 Lift the filter holder into the liquid coffee/boiler outlet. Turn it to the right to lock
into position .
Put one or two cups underneath
●
cup in the middle.
● Ensure the selector knob is on the boiler position (
on. Wait until the OK light glows then turn the selector knob to the coffee
position ( ).
6 When you've enough coffee – not too much otherwise it will be too weak,
(optimum dosage is 50ml per cup) return the selector knob to the boiler
position ( ). If you're not making any more coffee turn the selector knob to
the off position ( ).
7 Remove the filter holder by turning to the left.
● There will be water on the filter when you remove it: this is normal
8 To remove the used coffee from the filter holder, flip the lever on the handle so
that the end locates over the filter
upside down and tap out the grounds
Important
Never remove the filter holder while the coffee (
selected or while coffee is brewing – steam could shoot out and burn you.
to make coffee using filter pods
Important
If the filter for one cup is used after ground coffee has been used, it is
necessary to clear any ground coffee from around the liquid coffee/boiler outlet.
This is necessary to avoid water leakages from the filter holder and to ensure
optimum performance. Take care as the area may be hot.
1 Pre heat the machine as described on page 2. This will ensure that the coffee
is delivered at a hotter temperature. Fit the small filter into the filter holder
before fitting to the machine, making sure that the tab on the filter fits into the
slot on the filter holder.
2 Place the coffee pod into the filter making sure the pod is facing the correct
way .
3 Press the pod towards the lower part of the filter, making sure that the paper
flaps adhere to the inner part of the filter.
4 The pod needs to be well centred and placed in the filter.
5 Fit the filter holder into the liquid coffee/boiler outlet and turn to the right until it
locks into position .
6 Follow the points 'to make espresso'.
Note – use pods that conform to the ESE standard.
● Always follow the instructions on the package of the
pods for the correct positioning of the pods in the filter
to froth milk for cappuccino
Prepare the espresso as previously described
1 Make sure there is water in the tank.
2 Turn the selector knob to the steam position (
on indicating that the boiler has reached the correct temperature.
3 Part fill a jug with milk – the milk may increase up to three times in volume so
select a suitably sized jug.
● Cold semi skimmed milk gives the best results.
4 Position the jug under the steam/hot water nozzle
5 Place the nozzle into the milk about 30mm deep and turn the steam/hot water
knob in an anti clockwise direction. The milk will begin to increase in volume
and appear frothy. When the volume of the milk has doubled, fully immerse the
nozzle and continue heating the milk. Once the desired temperature is reached
(60ºC), stop the steam by turning the steam/hot water knob clockwise.
. If making one cup of coffee, centre your
), the boiler light will come
. Hold the lever in position then tip the unit
.
) or steam ( ) function is
). Wait until the OK light comes
.
● Never allow the milk to boil as this will spoil the flavour of the coffee.
6 Turn the selector knob back to the off position (
7 Pour the frothed milk into the cups containing the espresso coffee.
Important – Never operate the steam/hot water nozzle for longer than 2
minutes at one time.
hint - to prepare more than one cappuccino, first make all the coffees then at
the end prepare the frothed milk for all the cappuccinos.
to make espresso after frothing milk
Important
Never remove the filter holder from its housing immediately after using the
steam fuction.
If you're making espresso after frothing milk, you need to get rid of any over-hot
water that could burn your coffee. Here's how:
1 Place a container underneath the steam/hot water nozzle, ensuring the selector
knob is at the boiler position (
clockwise. Turn the selector knob to the coffee position (
water to flow out until the OK light comes on.
2 Turn the selector knob to the boiler setting (
the steam/hot water nozzle. Turn the steam/hot water knob in a clockwise
direction to close.
3 The unit is now ready to make coffee.
to boil water for other drinks, eg tea, fruit drinks.
1 Make sure the selector knob is in the off position (
2 Check that there is water in the tank.
3 Turn the selector knob to the boiler position (
4 Position a container under the hot water/steam nozzle.
5 When the OK light glows, turn the steam/hot water knob in an anti-clockwise
direction then the selector knob to the coffee/hot water position (
will come out of the steam nozzle.
6 To stop the flow of hot water return the selector knob to the off position (
then turn the steam/hot water knob in a clockwise direction.
Do not dispense hot water from the steam nozzle for longer than 20 seconds in
one operation.
cleaning
● Before cleaning, unplug and let everything cool.
Never immerse the appliance in water.
●
● Don't wash parts in the dishwasher.
tank, lid, filter holder
● Wash, rinse and allow to dry.
filter (one and two cup version)
● Wash and dry after every use.
● After approximately every 100 uses dismantle and clean more thoroughly as
described below.
● Remove the cap located on the underside of the filter by turning in the direction
indicated . Remove the crema device by pushing up from the underside
Separate the components of the crema device by pulling the gasket to the side
and removing the plastic disc and metal filter µ. Rinse parts thoroughly.
Clean the metal filter in hot water using a brush ¸. Make sure the holes in the
metal filter are not blocked. If necessary clean with a pin ¹. Dry the parts then
reassemble, making sure the parts are correctly assembled.
steam/hot water nozzle
● Prior to cleaning allow some hot water to flow out of the nozzle (see 'to boil
water for other drinks') but unplug and allow to cool before proceeding.
● Unscrew the nozzle by turning clockwise, then wash thoroughly. Check that the
three holes in the nozzle are not blocked
pin.
● Clean the steam/hot water delivery tube. Make sure the end is not blocked.
Screw the nozzle back onto the delivery tube.
●
cup stand, drip tray
Empty the drip tray regularly. You'll know when it is full, the red float in the
●
middle of the drip tray will rise and become visible in the centre hole on the cup
stand.
1 Wash then dry.
3
).
), then turn the steam/hot water knob anti
) and allow the
) to stop the water flowing from
).
).
. If necessary unblock them with a
). Hot water
)
.