Hoonved HD 40 BT Instrucciones Para El Uso Y El Mantenimiento página 44

ENGLISH
Every operation of installation, electrical or hydraulic
connection, programming, maintanance etc...has to
be carried out by QUALIFIED personnel, authorised
by the manufacturer;
any interventions carried out by UNQUALIFIED
personnell, may compromise the technician's own
safety, as well as the safety of other personnel (op-
erators, etc.) or of any other equipment connected to
the washing machine.
The manufacturer declines all responsability for
accidents or damage to persons or property caused
by failure to comply with the above listed provisions.
If the electrical cord is damaged, it must be replaced
by the manufacturer or by its technical service or by
a person with similar qualifications.
3.1 INSTALLATION (Fig. 5)
- After having removed the packing, check that the machine
is in a perfect condition and that all the parts have been
included.
- Position the machine in the required setting and level it
by means of the feet (17).
IMPORTANT
To have a correct opening/closing of the tank door it is ne-
cessary to assure a perfect sliding of the upper and lower
door lining up them with the body of the machine (Fig.5 -
letter A).You make the line-up adjusting the feet (17)
3.1.a Drain pipe connection (Fig. 5)
- Connect one end of the drain pipe to the overflow (12)
and the other to an already prepared drain trap.
IMPORTANT
To preview a pavement download with sifoide and to join
to the machine with the flexible tube to I equip making
so that the same one or in slope towards the download.
To make sure moreover that along the same one not
there are throttlings.
To assess that the outlet pipe to wall resists to a tem-
perature of 70°C.
3.1.b Connection to the water main (Fig. 5)
- Connect one end of the supplied inlet pipe (16) to the
solenoid valve (18) and the other end (16) to a 3/4" G
threaded cock, installing the filter in between.
ATTENTION
It is essential to connect the cold water delivery pipe to a
throttle cock in order to separate the water main from the
machine itself. Also check that there are no sharp bends.
ATTENTION
It is compulsory to replace the gaskets of the inlet
tube for water supplying, every time it is demounted
and mounted.
44
IMPORTANT
Part 3: For the technician
ATTENTION
If there is sand in the water main, it will be necessary to
install a filter between it and the machine.
The exercise pressure will not have to be inferior to the 2
advanced bars and to the 4 bars (200-400 kPa).
If the pressure is inferior, increase is advised to the instal-
lation of a pump pressure; if the pressure is advanced,
the application of a pressure reducer.
For having a good result he is advisable to have the water
of entrance with a not advanced hardness to the 10°F.
For advanced hardnesses to use cars with built-in wa-
ter softner or water softners to ion exchange or inverse
osmosis.
To respect eventual enforced National or Regional
norms rigorously.
The manufacturer declines all responsibility for dama-
ge to the machines caused by failure to comply with
the above listed provisions.
3.1.c Electrical connection (Fig. 5)
DANGER
- Before connecting to the electricity main, always
check that the data pertaining to the power source
correspond to those indicated on the identification
plate (11 Fig. 4) and that the main electric power
switch installed prior to the machine is discon-
nected "0" OFF.
- An appropriately sized omnipolar circuit-breaker
with a minimum 3 mm gap between its contacts
must be installed between the power supply main
and the machine.
- The manufacturer declines all responsibility for
accidents or damage to persons or property caused
by failure to comply with the above listed provisions.
- Connect the electrical power cable (14) to the main
switch installed prior to the machine.
- Connect the equipotential ground conductor to the
terminal .
The electrical power cable can NOT be replaced
•
by USER but only by technical.