Desoutter SCF Serie Manual De Instrucciones página 7

SCF Feed Screwdriver
TM
STATEMENT OF USE
The product after being fitted with a $ultable Oesoutter
screwfeedlng noufe fs designed for lnstafling threaded fasteners
supplied by a suitable Oessoutter screwfeeder. No other use
permitted.
GENERAL
j-
Recommended Inlet
hose
~~
I. {fr.~ :mm:_J
LUBRICATION
Thi$ IS a ORYUNE
tool
designed to operate
QO
a totally dry air line
I.e. one without any oil or water moisture.
ORYUNE
tools an
also operate on a fubficated or pcYtly lubricated
air line thus aDowlng easy lnterchangeabllrty with existing
instanaHons:lf lubrication is required an air line lubrfcator should be
fitted down stream of the filter. 'he ISO VC 1 S.
273283 =BP FGOOEP 27662 = ISOVGl
5
273273 = BP Q5618
DATA
Maximum air pressure Pma:1< =
6. 3 bar
Minimum air prenure P min
=
2.0 bar
Sound Pse<sure Level (dBA)
= 73± 2 re.CAGl-PNEUROP Te1t <ode
Vibration Level
(m/sec? re
ISO 8662 ("with 1lde h;indle
fitted)
A2300-R = 2.0-5.0 ('1.5-3.0) A2300-S = <2.5
A1600-R = 3.0-9.0 (*2.0..5.5) Al 600..S = <2.5
Al 100-R = 9.0-35.0("3.5-10.5) A1100-S = <2.5
AS50-R = 10.0-29.0("4.0-10.0) AS50-S = <2.5
Weight
=
0.9 kg.
@»
~
WARNING
BEFORE OPERATING THIS TOOL,
READ AND UNDERSTAND PNEUMATIC
SCREWDRJV!R SAFETY INSTRUCTIONS
PART NO. 370273
Printed In England
GD
SETTING UP INSTRUCTIONS (See Flgurel)
Connect a suitable Oesoutt~ nozzle to the tool, ensuring the nozzle
Is correctly set up (see
s~ke
sheet '406723, and sec.ured
n
place
with Part No. 392193. Connect the pneumatic control tubes from
the screwfeeder to the corresponding coloured connectors.
Connect the recommended Inlet hose to the fnJet
bolt,
and
the
other end to the air supply connector on
the
screwfeeder.
b,_
WARNING: SECURELY FASTEN SCREW FEED TUBE
ill
AT BOTH ENDS BEFORE OPERATING.
OPERATING INSTRUCTIONS
A/STOOLS
Wlth the correct accessory
fitted
connect the tool to the air supply.
Grip the
toof
around the motor case and press the tool Into the
fixing that Is to be tlghtened.The motor Wt11 start and
the
noule
retract.The motor will start and tighten the
fixing
to the required
lorque set by adjusting the ten.srons on the clutch spring.
AJ.
this
point
the
Internal drive Is disengaged and the air lo the motor cut
off.
After an ndjustabfe fnt(.>fVal (.see service sheet Part No. 394113) lhe
noule is advanced and another fastener led to the nozzle jam.
A/RTOOLS
With
the
correct accessory
fitted
connect the tool to the air supply.
Grip the tool around the motor case and press the tool Into the
fixing that b to be tightened. The motor will start and the noule
retract The motor will start and tighten the fixing to the required
torque
set
by adjusting the tensions oo the clutch spring. Motor wfll
stop when
tool I~
removed from fixing.
After an adfustable Interval (see service sheet Part No. 39-4113) the
noule
fs advanced and another faslencr fed to the nozzle Jaws.
b,_ WARNING: CARE SHOULD BE TAKEN TO ENSURE
ill
NOTHING BECOMES TRAPPED BETWEEN THE
NOZZLE AND TOOL BODY WHEN THE NOZZLE
RETRACTS.
&
WARNING
BEWARE OF TRAPPING FINGERS WHEN NOZZLE RETRACTS.ONLY
GRIP THE TOOL AROUND THE MOTOR CASE DISCONN£CT FROM
AIR SUPPLY BEFORE PERFORMING ANY ADIUSTMENTS OR
SERVICING.
7
of 23
MAINTENANCE INSTRUCTIONS
l. Servicing should be carried out at Intervals of 1000 hours.
2. Disa:nemble wllh reference to figurl! 2 & 3 (arrows indicate
dJrectlon of dlsmantllng).
3. Aeptace as necessary all
·o·
1ing:1, seals, bearings and rotor
blades. See R!rvice kits.
0
""""-a'"' ;'""'"
4. When disposing of components, lubricants,
J,, ...
ensure that
the relevant safety procedures are tarried
out.
5.
~anemble
with reference to Figure 2 & 3. Torque values.
stated
are for assembly
(± 10%). I
7.
~
lndlc.ates direction of dismantling.
6. Setting the push rod, see Figure 4.
I
8, Overmould should be wiped clean with a groeral purpose,noos
aggressive degreasant.
i ,
&
WARNING
®
THE ROTOR BLADES IN THIS TOOL HAVE A PTFE CONTENT. THE
NORMAL HEALTH AND SAFETY RECOMMENDATIONS
CONCERNING PTFE MUST BE OBSERV{D WHEN HANDLING THESE
ROTOR BLADES. :
'
(1) DO NOT SMOKE.
I
(2) MOTOR COMPONENTS MUST BE WASHED WITH CLEANING
FLUID AND NOT BLOWN CLEAR WITH AN AIR LINE.
' (3) THE SILENCER MUST BE REPLACED WHEN DIRTY,
DO
NOT
CLEAN AND RE-USE.
i
(4)
WASH HANDS BEFORE COMMENCING
ANY
OTHER
ACTMTY.
I
'
Cl 1999 Oesoutter, HP2 7DR, UK
i
All rights
t~rved.
Any unauthorized use or copying of the <:ontents
Of
part thereof Is prohibited. This applies in partlcular lo trademarks,
model denominations, part numbers and drawingi.
I
Use only authorizC'd parts. Any damage or malfunction caused by the
use
of
unauthorized parts is not covered by Warranty or Product
Liability. '
Part No. 409893 lnoe 3. 9. 99
i
I