NuTone ALLURE WS3 Serie Manual De Instrucciones página 6

NON-DUCTED FILTERS
If hood is to be installed Non-Ducted:
Purchase a set of (2) Non-Ducted Filters from your local
distributor or retailer and attach them to the aluminum mesh
filters.
NOTE: For models that are installed in the non-ducted mode, the
most effective operation is achieved at speeds 1 and 2.
These speeds provide the most efficient and quiet
operation during cooking, while maximizing the benefits
of the recirculating filtration system.
OPERATION
Fan: 4 push button switches. Push any button to select one of the
four fan speeds. Press another button to change fan speed. Push
the same button to turn fan off. A light above each fan button
indicates the fan speed.
Lights: Press "on/off" button and lights will come on at their previ-
ous light level. Press button again to turn lights off. To increase
light level, press the "+" button. To reduce light level, press the "-"
button. There are 3 light levels to select.
Delay Off: While fan is running, press the "delay" button to allow
the fan to run for 10 minutes and then turn itself off. Filter Change Indicator: The light above "filter" will come on when
it is time to clean your grease filters or check your non-ducted
filters. After replacing the cleaned, or new filters, press the "filter"
button to turn off the indicator light.
Heat Sentry System: Your range hood is equipped with an ad-
vanced Heat Sentry system.
The advanced Heat Sentry system monitors temperature and au-
tomatically adjust the fan to the appropriate setting.
1) If the fan is on, the Heat Sentry system will increase the fan
setting when the temperature is elevated. If the temperature
continues to rise, the Heat Sentry system will continue to in-
crease the fan setting until the temperature is stabilized or re-
duced. The flashing light above the fan button shows the Heat
Sentry system fan setting. Once the temperature has reduced,
the Heat Sentry system will change the fan to the original set-
ting.
2) If the fan is on or off, the Heat Sentry system will automatically
turn the fan on at its highest speed when the temperature is
above normal. When the Heat Sentry system is on, the light
above the fan button B (Boost) will flash on and off. After the
temperature has lowered to normal, the fan will change to the
setting prior to the Heat Sentry turning on.
Fuse: The hood control contains a fuse to protect it from power
surges. If the fuse has opened (blown), the green fan-level indica-
tors will operate properly when the fan buttons/switches are
pressed - but the fan and lights will not turn on.
The fuse is a 5 x 20 mm, 10 Amp, Fast-Acting, 125V (min.). Com-
mon manufacturer and part numbers are: Littlefuse, 217010;
Bussmann, GMA10A; Wickmann, 1942100. Radio Shack, Digikey
(1-800-344-4539), and most electronic supply stores have them
in stock.
To replace the fuse:
1. Disconnect power at service entrance.
2. Remove filters, bottom panel, light wire harness, and air chute.
®
3. Remove and inspect fuse. If it is not open (blown), additional
diagnostics need to be done.
4. Install new fuse.
5. Re-assemble air chute, light wire harness, bottom panel, and
filters.
6. Turn on power and check hood/control operation.
CLEANING
WARNING: To reduce the risk of electric shock,
disconnect from power supply before cleaning.
Aluminum mesh filters: Clean frequently using hot water and a
mild detergent. Filters are dishwasher safe.
Charcoal filters: Clean filter surfaces frequently with a damp cloth
and a mild detergent. DO NOT immerse filters in water or put in
dishwasher. The special "Clean Sense" feature indicates when
the filter is to be replaced. The blue and yellow strips will blend to
green when it is time to change the filter. The "Clean Sense"
feature works best when facing toward the cooking surface.
To clean hood: Remove filters. Use a damp cloth and a mild deter-
gent to wipe all grease-laden surfaces. Do not use abrasive cloth,
steel wool pads, or scouring powder on the Teflon
cover or on any painted surface. Use care when cleaning blower
wheel - it must not become bent or misaligned. DO NOT ALLOW
WATER TO ENTER MOTOR. Make sure all surfaces are com-
pletely dry before re-installing filters and restoring power.
Motor is permanently lubricated. Do not oil or disassemble motor.
Teflon ® is a registered trademark of DuPont.
®
ALLURE WS3 SERIES
RANGE HOOD
Page 6
® -coated bottom