Bosch ART 23-10,8 LI Manual Original página 15

OBJ_BUCH-2510-001.book Page 15 Wednesday, July 22, 2015 9:20 AM
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
22.07.2015
Mounting and Operation
Action
Delivery Scope
Connecting the shaft
Mounting the Cutting Guard
Blade Fitting
Handle Assembly
Charging the Battery Pack
Inserting and removing the battery
pack
Check the blade
Replace the blade
Storage blade
Switching On and Off
Working Advice
Maintenance, Cleaning and Storage
Selecting Accessories
Starting
For Your Safety
 Warning: Switch off and remove battery from machine
before adjusting or cleaning.
 The blade continues to rotate for a few seconds after
the cordless trimmer is switched off. Allow the mo-
tor/blade to stop rotating before switching "on" again.
 Do not rapidly switch off and on.
 Only use Bosch approved cutting elements. Cutting
performance will vary with different cutting elements.
Battery Charging
 Do not use other battery chargers. The supplied battery
charger is designed for the Lithium-Ion battery in your gar-
den product.
 Observe the mains voltage! The voltage of the power
supply must correspond with the data given on the name-
plate of the battery charger. Battery chargers marked with
230 V can also be operated with 220 V.
Bosch Power Tools
The battery is equipped with temperature monitoring that al-
lows charging only in the temperature range between 0 °C
and 45 °C. In this manner, a high battery service life is
achieved.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The "Electronic Cell Protection (ECP)" protects the lithium-
ion battery against deep discharging. When the battery is run
Figure Page
down or discharged, the garden product is shut off by means
of a protective circuit: The blade no longer moves.
1 219
2 219
been automatically switched off. The battery can be dam-
aged.
3 220
4 221
Battery charge-control indication
The battery charge-control indicator on the handle of the
product will indicate a low charge condition of the battery by
flashing three times when the On/Off switch is pressed. If this
5 221
occurs, please remove the battery and recharge.
6 222
Charging Procedure
7 222
The charging procedure starts as soon as the mains plug is
8 222
plugged into the socket and the battery is then inserted into
the battery charger .
9 223
Due to the intelligent charging method, the charging condi-
10 223
tion of the battery is automatically detected and the battery is
11 223
charged with the optimum charging current, depending on
battery temperature and voltage.
12 224
This gives longer life to the battery and always leaves it fully
charged when kept in the charger for storage.
Note: The charging procedure is only possible when the bat-
tery temperature is within the allowable charging tempera-
ture range, see section "Technical Data".
Flashing Battery Charge Indicator
Continuous Lighting of the Battery Charge
Indicator
in the allowable charging temperature range, and cannot be
charged for this reason. The battery is charged as soon as the
allowable charging temperature range is reached.
When the battery is not inserted, continuous lighting of the
battery charge indicator indicates that the mains plug is in-
serted in the socket and that the battery charger is ready for
operation.
English | 15
Do not continue to press the On/Off
switch after the garden product has
The charging procedure is signalled by a
flashing battery charge indicator .
Continuous lighting of the battery
charge indicator indicates that the
battery is fully charged or that the
temperature of the battery is not with-
F 016 L81 125 | (22.7.15)