Optional Accessories; Recommended Blades Available; Protecting The Environment - DeWalt DW711 Traducido De Las Instrucciones Originales

ENGLIS H
Cleaning
Before use, carefully check the upper blade guard, movable lower blade
guard as well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or workpiece particle cannot lead to
blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and guards
disconnect the machine from the power supply and follow the instructions
given in section Mounting the Saw Blade. Remove the jammed parts and
reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing with dry
air as often as dirt is seen collecting in and around the air vents.
Wear approved eye protection and approved dust mask when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals
may weaken the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool into a
liquid.
WARNING: To reduce the risk of injury, regularly clean the
table top.
WARNING: To reduce the risk of injury, regularly clean the
dust collection system

Optional Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
E
accessories with this tool could be hazardous. To reduce the
risk of injury, only D
be used with this product.
DUST EXTRACTION
A separate dust kit is available for optimal dust extraction (DE7779).
CLAMPING THE WORKPIECE (FIG. A3)
• In most cases, the action of the blade is sufficient to hold the material
firmly against the fence.
• If the material has a tendency to lift or come forward from the fence,
preferably use the optional material clamp (23).
• Always use the clamp if cutting non-ferrous metals.
SAWING SHORT WORKPIECES (FIG. A3, A4)
It is advisable to use the length stop for short workpieces (27) both for batch
sawing and for short individual workpieces of different lengths. The length
stop can only be used in conjunction with a pair of optional guide rails (21).
SAWING LONG WORKPIECES (FIG. A3)
WARNING: Always support long workpieces.
Figure A3 shows the ideal configuration for sawing long workpieces when
the saw is used free-standing (all items available as an option). These items
(except the legstand and the material clamp) are required both on the infeed
and the outfeed side:
20 Table end plate for support the rails; also when working on an existing
bench.
21 Guide rails (500 or 1,000 mm).
22 Material support plates.
23 Material clamp.
24 Swivelling stop.
30
WALT, recommended accessories should
E
25 Stands to support the guide rails. The height of the stands is adjustable.
WARNING: Do not use the stands to support the machine!
26 Legstand (supplied with mounting instructions).
Procedure
1. Place your saw on the legstand and fit the guide rails.
2. Firmly screw the material support plates (22) to the guide rails (21). The
material clamp (23) now functions as a length stop.
3. Install the table end plates (20).
4. Install the swivelling stop (24) to the rear rail.
5. Use the swivelling stop (24) to adjust the length of medium and long
workpieces. It can be adjusted sideways or swung out of the way when
not in use.
USING THE ROLLER TABLE (FIG. A3, A5)
The roller table (29) makes the handling of large and long pieces of wood
very easy (fig. A5). It can be connected either to the left or to the right of the
machine. The roller table requires the use of the optional legstand (fig. A3).
WARNING: Assemble the roller table following the instructions
supplied with the legstand.
• Replace the short support bars provided with the legstand with the
irregular rails from the table on the side the table is to be used.
• Follow all instructions provided with the roller table.

Recommended Blades Available

Type of blade Blade dimensions
(diameter x bore
x no. of teeth)
DT1529 series 40 260 x 30 x 24
DT1530 series 40 260 x 30 x 80
DT1736 series 60 260 x 30 x 58
DT1737 series 60 260 x 30 x 80
Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. This product must not be disposed of with
normal household waste.
Should you find one day that your D
if it is of no further use to you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of recycled
materials helps prevent environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection of electrical products
from the household, at municipal waste sites or by the retailer when you
purchase a new product.
D WALT provides a facility for the collection and recycling of D
E
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D WALT office at the address indicated in this manual.
E
Alternatively, a list of authorised D
of our after-sales service and contacts are available on the Internet at:
www.2helpU.com.
Usage
For general purpose, ripping and
cross-cutting of wood and plastics
TCG for use with aluminum
ATB for fine cutting of manmade and
natural wood
TCG for extra fine cutting of manmade
and natural wood
WALT product needs replacement, or
E
WALT
E
WALT repair agents and full details
E