CYBEX ONYX Guia Del Usuario página 6

ONYX/TOPAZ ASSEMBLY INSTRUCTION
DELIVERY STATUS
1. OPENING THE STROLLER
a) Release the folding lock lever.
b) Open the stroller.
c) Push the pedal button down until the locking system is engaged.
2. ASSEMBLING THE HANDLES
ATTENTION: THE PINS ON BOTH SIDES MUST BE ENGAGED.
3. ASSEMBLING THE FRONT WHEELS
– Fit the front wheels to the end of the frame until they engage with a "click".
4. ASSEMBLING THE REAR WHEELS
ATTENTION: THE WHEEL SYSTEM WITH THE BRAKE PEDAL MUST BE FITTED TO THE RIGHT
SIDE OF THE BUGGY (VIEWED FROM BEHIND THE BUGGY).
ATTENTION: THE PINS ON BOTH SIDES MUST BE ENGAGED.
Ensure the bowden cable is inserted into the clips on both sides.
5. ATTACHING THE BUMPER BAR (TOPAZ ONLY)
a) Slide in latches on left and right side into gadgets sewn into the seat fabric.
b) Press buttons on left and right end of the bumper bar to tade it off.
6. FOLDING THE STROLLER
Remove all contents from the basket. Close the canopy. Remove the bumperbar.
a) Push the primary lock lever underneath the pedal button.
b) Lift the activated primary lock lever to release the stretching system.
c) Push down the secondary lock lever (extended bar on the right side of the
locking system).
d) Grip handles and push forward on the stroller to fold it.
e) Press folded stroller until the fold lock is engaged. Its recommended to fasten
the harness before folding the stroller.
7. OPENING THE STROLLER
a) Release the fold lock lever.
b) Open the stroller
c) Push the pedal button down until the locking system is engaged.
WARNING: ENSURE THAT ALL LOCKING DEVICES ARE ENGAGED BEFORE USE.
8 . USING THE BRAKES
a) Engage Brake
b) Release Brake
9 . AUTOMATIC FRONT WHEEL SWIVEL LOCKS – LOCK – UNLOCK
a) Push the Front Swivel Lock Lever until it "clicks". It can be activated in any wheel
positions. The swivel Lock will engage automatically when it reaches the right
position.
b) Lift the Front Swivel Lock Lever up again to release the Swivel Lock.
8
10. CANOPY
– Attach the canopy adaptor on to the inside of the frame tubes of the buggy.
– To remove the canopy reverse procedure.
– Extend the canopy and place canopy rear flap behind the seat.
– Use the zipper to attach or detach the winter extension.
– Lie-flat position: Put the rear flap over the seat's back rest and fixate it with the
two velcros underneath.
– The canopy is adjustable to various positions.
11. USING THE HARNESS SYSTEM
a) To fasten the harness system insert left and right side fasteners into the central
harness buckle.
b) To tighten the belts pull the strap on the front of the central harness buckle.
c) To release the belt system press the release button located on the seat in front
of the belt lock while pulling at the shoulder belts.
d) To release the fasteners squeeze the grooves on left and right side of the central
harness buckle.
e) Adjust the length of the crotch strap with the corresponding slider.
WARNING: ALWAYS USE THE CROTCH STRAP IN COMBINATION WITH THE WAIST BELT.
12 . ADJUSTING THE HARNESS SYSTEM FOR NEWBORNS
a) Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the bottom of the backrest under the seat cover.
b) Completely pull the shoulder straps out of the holes in the backrest.
c) Feed the shoulder straps through the two bottom holes. Make sure to feed the
straps back through the holes in the backrest mechanism and re-attach them
to the triangle.
d) To adjust the length of the shoulder straps to newborns please attach the inner
loop of the shoulder strap ends to the triangular ring. Switch back to the upper
holes as soon as the shoulder straps do no longer fit over the child´s shoulders.
13. REMOVING THE HAEDHUGGER AND SHOULDER PADS (TOPAZ ONLY)
Remove the haedhugger as soon as the haedhuggerå does no longer fit over the
child´s shoulders.
a) Remove the velcros of the haedhugger on the top leh and right side on the
back of the seat cover.
b) Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the boKom of the backrest under the seat cover.
c) Completely pull the shoulder straps out of the holes in the backrest.
d) Pull the shoulder straps through the shoulder pads and the hadhugger. Make
sure to feed the straps back through the holes in the backrest mechanism and
attach them to the triangle. You can use the haedhugger and the shoulder
pads separately.
14. REMOVING THE SEATCOVER
a) Slightly fold the stroller to reduce tension.
b) Remove the canopy from the stroller, if attached.
c) Take the seat cover's hooks (3) off the frame on left and right side
d) Open the press buttons (4) of the straps connected to the seat side panels and
the basket rear tube.
e) Open the fl aps (5) which are fi xed with velcro over the tubes, one on each side.
f) Feed the strap with the slider (6) of the central harness buckle through the hole
in the seat fabric.
g) Feed the loops on the end of the shoulder straps through the triangle in the
backrest (7).
h) Feed the shoulder straps through the holes in the seat fabric (8).
i) Open the press buttons which are on the left and the right side from the seat on
the bottom from the fabric.
j) Pull the seat cover over the belt shifting button on the seat.
k) Slide the fabrics from the seat base tubes.
l) Reverse this procedure to refi t the seat cover and the harness. Make sure that
the seat tubes slide back into the pockets inside the seat cover.
15. RECLINING THE LEG REST
a) Press the leg rest on both front edges and push down.
b) Simply lift the leg rest to put it back to the starting position.
16. RECLINING THE SEAT
a) Pull the recline lever at the back of the seat in order to recline the backrest to
the 4 different positions.
b) To raise lift the complete backrest up to required position.
17. CARRYING THE STROLLER
– Pull the flexible carring handle on right rear tube and lift the stroller.
18. ATTACHING THE RAINCOVER (OPTIONAL)
a) Extend the rain cover over the stroller like shown in the image
b) To fit the rain cover fasten the velcro strips around the frame at the top and
bottom on both sides of the buggy.
19. WARRANTY
The following warranty applies solely in the country where this product was initially
sold by a retailer to a customer. The warranty covers all manufacturing and material
defects, existing and appearing, at the date of purchase or appearing within
a term of two (2) years from the date of purchase from the retailer who initially
sold the product to a consumer (manufacturer's warranty). In the event that a
manufacturing or material defect should appear, we will – at our own discretion –
either repair the product free of charge or replace it with a new product. To obtain
such warranty it is required to take or ship the product to the retailer, who initially
sold this product to a customer and to submit an original proof of purchase (sales
receipt or invoice) that contains the date of purchase, the name of the retailer and
the type designation of this product. This warranty shall not apply in the event that
this product is taken or shipped to the manufacturer or any other person other than
the retailer who initially sold this product to a consumer. Please check the product
with respect to completeness and manufacturing or material defects immediately
at the date of purchase or, in the event that the product was purchased in distance
selling, immediately after receipt. In case of a defect stop using the product and
take or ship it immediately to the retailer who initially sold it. In a warranty case the
product has to be returned in a clean and complete condition. Prior to contacting
the retailer, please read this instruction manual carefully. This warranty does not
cover any damages caused by misuse, environmental influence (water, fire, road
accidents etc.) or normal wear and tear. It does solely apply in the event that the
use of the product was always in compliance with the operating instructions, if any
and all modifications and services were performed by authorized persons and if
original components and accessories were used. This warranty does not exclude,
limit or otherwise affect any statutory consumer rights, including claims in tort and
claims with respect to a breach of contract, which the buyer may have against
the seller or the manufacturer of the product.
20. CARE INSTRUCTIONS
– wash separately
– gentle action wash warm water
– do not bleach
– do not tumble dry
– do not iron
– do not dry clean
UK – AFTER SALES SERVICE:
If you need assistance, spare parts or you are unhappy with any aspect
of the goods please contact Customer Care on: +44 (0)845 268 2000,
or e-mail us at: [email protected].
Visit our website at www.mamasandpapas.com for the latest product
information.
9