Gas Oven; Electric Hob; Electric Oven; Replacing Components - KBS 700 Serie Instrucciones Para Instalación, Uso Y Mantenimiento

• Insuficient gas supply pressure.
• Blocked tubing or nozzle.
• Defective gas tap or valve.
• Igniter defective or not properly connected.
• Igniter or igniter wire defective.
Pilot burner goes out during use
Possible causes:
• Insuficient gas supply pressure.
• Defective gas tap or valve.
• Defective thermocouple or insuficient heating.
• Thermocouple incorrectly connected to gas tap or valve.
• Knob of gas tap or valve not pressed suficiently.
The main burner does not light ( even though pilot is lit )
Possible causes:
• Insuficient gas supply pressure.
• Blocked tubing or nozzle.
• Defective gas tap or valve.
• Defective burner ( gas outlet holes clogged ).
21.3

GAS OVEN

The pilot burner does not light
Possible causes:
• Insuficient gas supply pressure.
• Blocked tubing or nozzle.
• Defective gas tap or valve.
• Igniter defective or not properly connected.
• Igniter or igniter wire defective.
Pilot burner goes out during use
Possible causes:
• Insuficient gas supply pressure.
• Defective gas tap or valve.
• Defective thermocouple or insuficient heating.
• Thermocouple incorrectly connected to gas tap or valve.
• Knob of gas tap or valve not pressed suficiently.
The main burner does not light ( even though pilot is lit )
Possible causes:
• Insuficient gas supply pressure.
• Blocked tubing or nozzle.
• Defective gas tap or valve.
• Defective burner ( gas outlet holes clogged ).
Heating cannot be adjusted
Possible causes:
• Defective gas valve.
21.4

ELECTRIC HOB

The hotplate does not heat.
Possible causes:
• Hotplate defective.
21.5

ELECTRIC OVEN

The appliance does not heat.
Possible causes:
• Temperature thermostat defective.
• Heating elements defective.
• Safety thermostat tripped.
Heating cannot be adjusted
Possible causes:
• Temperature thermostat defective.
21.6 GRILL
The grill does not switch on
Possible causes:
• Defective energy regulator
• Le resistenze sono guaste.

22 REPLACING COMPONENTS

REMINDERS FOR REPLACING COMPONENTS.

• Disconnect the appliance electric supply, if present, before
carrying out any operation.
• After replacing a gas system component, check for gas leaks
at connection points.
• After replacing an electrical system component, check it is
correctly wired.
22.1

GAS HOB

Replacing the gas tap.
• Remove the control panel.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the pilot burner and thermocouple.
• Remove the control panel.
• Remove the panstand grids and burners
• Remove the 3 screws securing the venturi to the hob and pull
the venturi out by approx. 10 cm.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
22.2

SOLID TOP GAS HOB/SIMPLE SERVICE

Replacing the gas tap and piezo igniter
• Remove the control panel.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the main burner, pilot burner, thermocouple and
igniter
• Remove the hotplate.
• Remove the control panel and internal guards.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
22.3 GAS OVEN
Replacing the gas valve and piezo igniter
• Remove the control panel.
• Remove the bulb from its seat on the side of the oven.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
9