Safety Precautions; Specifications - ekwb EK-AIO 120 D-RGB Manual De Instrucciones

This product is intended for installation by expert users only. Please, consult with a qualifi ed
technician. Improper installation may result in damage to your equipment. EK Water Blocks
assumes no liability whatsoever, expressed or implied, for the use of these products or their
installation. The following instructions are subject to change without notice. Please visit our web
site at www.ekwb.com for updates.
NOTE ON ENVIRONMENTAL PROTECTION:
After the implementation of the European Directive 2012/19/EU in the national legal system, the
following applies:
• Electrical and electronic devices may not be disposed of with domestic waste.
• Consumers are obliged by law to return electrical and electronic devices at the end of their
service lives to the public collecting points set up for this purpose or point of sale. Details to
this are defi ned by the national law of the respective country. This symbol on the product, the
instruction manual or the package indicates that a product is subject to these regulations.
By recycling, reusing the materials or other forms of utilising old devices, you are making an
important contribution to protecting our environment.

1. SAFETY PRECAUTIONS

1. Keep and store the product away from the reach of children.
2. Check the component list and condition of the product before installation. If you encounter a
problem, contact the shop where you have purchased the product to get a replacement or a refund.
3. EKWB d.o.o. is not responsible for any damages due to external causes, including but not
limited to: improper use, problems with electrical power, accident, neglect, alteration, repair,
improper installation, and improper testing.
4. CPU and motherboard are subject to damage if the product is incorrectly installed.
5. The excessive force exerted on the fan may cause damage to the fan and/or system.
6. This product is a CPU liquid cooling solution kit, comprising of individual original EKWB parts.
Combining this liquid cooling unit with parts, other than EK Water Block products, may lead to
warranty loss.
7. Product design and specifi cations may be revised to improve quality and performance.
8. You must not run the pump below 20% RPM. The pump must stay within a 20-100% PWM
duty cycle at all times. We recommend to always run the pump at 100%.

2. SPECIFICATIONS

Model
Dimensions
Radiator
Fin material
Dimensions
Speed
Life Expectancy
Fan
Bearing Type
Connector
Rated Voltage
Dimensions (mm)
RPM
Pump
Life Expectancy
Noise Level
Input Current
Model
Dimensions
Radiator
Fin material
Dimensions
Speed
Life Expectancy
Fan
Bearing Type
Connector
Rated Voltage
Dimensions (mm)
RPM
Pump
Life Expectancy
Noise Level
Input Current
- 4 -
EK-AIO 120 D-RGB EK-AIO 240 D-RGB
157x120x27 mm 277x120x27 mm
Al Al
120x120x25 mm 120x120x25 mm (2x)
600-2200 RPM ±10% 600-2200 RPM ±10%
(PWM: 25-100%) (PWM: 25-100%)
50,000 hours 50,000 hours
Fluid Dynamic bearing (FDB) Fluid Dynamic bearing (FDB)
4-Pin 4-Pin
12V 12V
88x70x53 mm 88x70x53 mm
850-2600 RPM ± 10% 850-2600 RPM ±10%
(PWM: 20-100%) (PWM: 20-100%)
50,000 hours 50,000 hours
23 dB 23 dB
0.65 ±10% A 0.65 ±10% A
EK-AIO 360 D-RGB EK-AIO 280 D-RGB
397x120x27 mm 313x140x27 mm
Al Al
120x120x25 mm (3x) 140x140x25 mm (2x)
600-2200 RPM ±10% 500-2000 RPM +-10%
(PWM: 25-100%) (PWM: 25-100%)
50,000 hours 50,000 hours
Fluid Dynamic bearing (FDB) Fluid Dynamic bearing (FDB)
4-Pin 4-Pin
12V 12V
88x70x53 mm 88x70x53 mm
850-2600 RPM ±10% 850-2600 RPM ±10%
(PWM: 20-100%) (PWM: 20-100%)
50,000 hours 50,000 hours
23 dB 23 dB
0.65 ±10% A 0.65 ±10% A