Pc-Link Functions; Installation And Data Transmission; Data Memory; Viewing The Stored Values - Microlife BP A200 AFIB Manual Del Usuario

Ocultar thumbs Ver también para BP A200 AFIB:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18
tion (AFIB). If AFIB is present during blood pressure measurement,
the AFIB Indicator is displayed. In this case, the result may deviate
from your normal blood pressure. It is highly recommended to take
an additional measurement an hour later to increase the specificity
of the detection. In most cases, this is no cause for concern.
However, if the symbol appears on a regular basis (e.g. several
times a week with measurements taken daily) we advise you to visit
your doctor. Please, provide the following explanation:
Information for the doctor on frequent appearance of the
atrial fibrillation indicator
This instrument is an oscillometric blood pressure monitor that
also analyses pulse frequency during measurement. The instru-
ment is clinically tested.
The arrhythmia symbol is displayed after the measurement, if atrial
fibrillations occur during measurement. If the symbol appears more
frequently (e.g. several times per week on measurements
performed daily) we recommend the patient to seek medical advice.
The instrument does not replace a cardiac examination, but
serves to detect atrial fibrillations at an early stage.
Sometimes the device will detect atrial fibrillation even when
it is not there. This can happen if the arm moves during the
reading or another rhythm problem is present. Keep the arm
still during the reading. Visiting your doctor with this device
may be necessary to check out any rhythm problems.
This device may not detect atrial fibrillation in people with
pacemakers or defibrillators.

6. PC-Link Functions

This device can be used in connection with a personal computer
(PC) running the Microlife Blood Pressure Analyser (BPA) software.
The memory data can be transferred to the PC by connecting the
monitor via cable with the PC.
If no CD and cable is included download the BPA software from
www.microlife.com and use an USB cable with Mini-B 5 pin
connector.

Installation and data transmission

1. Insert CD into CD ROM drive of your PC. The installation will
start automatically. If not, please click on «SETUP.EXE».
2. Connect the monitor via cable with the PC; no need to switch
the device on. 3 horizontal bars will appear on the display and
last for 3 seconds.
BP A200 Afib
3. The bars will then flash to indicate that the connection between
PC and device is successfully made. As long as the cable is
plugged, the bars will keep flashing and buttons are disabled.
During the connection, the device is completely controlled
by the computer. Please refer to the «help» file for software
instructions.

7. Data Memory

At the end of each measurement, this instrument automatically
stores the result, including date and time.

Viewing the stored values

Press the M-button 2 briefly, when the instrument is switched off.
The display first shows «M» AS and then a value, e.g. «M 17». This
means that there are 17 values in the memory. The instrument
then switches to the last stored result.
Pressing the M-button again displays the previous value. Pressing
the M-button repeatedly enables you to move from one stored
value to another.

Memory full

Pay attention that the maximum memory capacity of 200 is
not exceeded. When the memory is full, the old values
are automatically overwritten with new ones. Values
should be evaluated by a doctor before the memory
capacity is reached – otherwise data will be lost.

Clearing all values

If you are sure that you want to permanently remove all stored
values, hold down the M-button (the instrument must have been
switched off beforehand) until «CL» appears and then release the
button. To permanently clear the memory, press the M-button
while «CL» is flashing. Individual values cannot be cleared.

8. Battery Indicator and Battery change

Low battery

When the batteries are approximately ¾ empty the battery symbol AR
will flash as soon as the instrument is switched on (partly filled battery
displayed). Although the instrument will continue to measure reliably,
you should obtain replacement batteries.
Flat battery – replacement
When the batteries are flat, the battery symbol AR will flash as soon
as the instrument is switched on (flat battery displayed). You cannot
take any further measurements and must replace the batteries.
EN
5
Tabla de contenido
loading

Tabla de contenido