Additional Safety Rules For Belt Sanders - SPARKY MBS 976 Instrucciones De Uso Originales

ments, changing accessories, or storing
power tools. Such preventive safety meas-
ures reduce the risk of starting the power tool
accidentally.
d) store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) maintain power tools. check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may affect the power tool's operation. if
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazard-
ous situation.
5. sERvicE
a) Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
IV - Additional safety rules
for belt sanders
▪ Use safety equipment including safety goggles
or shield, ear protection, dust mask and protec-
tive clothing including safety gloves.
▪ always remove the plug from the mains
socket before making any adjustments or
maintenance, including changing the sand-
ing belt.
▪ Fully unwind cable drum extensions to avoid
potential overheating.
▪ When an extension cable is required, you must
ensure that it has the right ampere rating for
your power tool and is in safe electrical condi-
tion.
▪ After long working periods external metal parts
and accessories could be hot.
▪ If possible, always use clamps or a vice to hold
Original instructions
your work.
▪ Always switch off before you put the sander
down.
▪ Do not force the sander; let the tool do the work
at a reasonable speed. Overloading will occur
if too much pressure is applied and the motor
slows resulting in inefficient sanding and pos-
sible damage to the sander motor.
▪ The dust, separated while processing materi-
als, containing quartz (SiO2) is dangerous to
your health. Do not process materials contain-
ing asbestos
▪ When sanding wood, always connect the dust
bag or use a dust extraction system.
▪ Before using the sander with metal, always
remove the dust bag from the outlet as sparks
may ignite the dust or the bag.
▪ Do not continue to use worn, torn or heavily
clogged sanding belts.
▪ Do not touch the moving sanding belt.
▪ Ensure that you have removed foreign objects
such as nails and screws from the work before
commencing sanding.
▪ Rags, cloths, cord, string and the like should
never be left around the work area.
WaRNiNg: Before connecting a tool
to a power source (mains socket power point
receptacle, outlet, etc.) be sure that the volt-
age supply is the same as that specified on the
nameplate of the tool. A power source with a
voltage greater than that specified for the tool
can result in serious injury to the user, as well
as damage to the tool.
▪ If in doubt, do not plug in the tool. Using a power
source with a voltage less than the nameplate
rating is harmful to the motor.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of mis-
use. The user and not the manufacturer shall
be liable for any damage or injury resulting from
such cases of misuse.
▪ To use this tool properly, you must observe the
safety regulations, the assembly instructions
and the operating instructions to be found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised
at all times if they are in the area in which the
tool is being used. It is also imperative that you
observe the accident prevention regulations in
5
EN