Homelite F-3045 Manual De Utilización página 25

Trimmer/Brushcutter-17 lgs
GB
F D E
OPERATION
Never use a blade after hitting a hard object without
first inspecting it for damage. Do not use if any
damage is detected.
Scythe, the broad sweeping of the unit back and forth
from side to side, with TRI-ARC blade only.
STARTING AND STOPPING (Fig. 16 & 17)
NOTE: The unit is equipped with an automatic choke
feature. The starting instructions for this feature are
different from units with a manual choke. Be sure to read
and follow the starting instructions below.
WARNING
Never start or run the engine inside a closed or
poorly ventilated area; breathing exhaust fumes
can kill.
TO START A COLD ENGINE:
1. Lay trimmer on a flat, bare surface.
2. Push primer bulb (56) 8 to 10 times.
NOTE: Do not squeeze the throttle trigger (6) before
engine starts. Squeezing the throttle trigger at this time
will prevent the unit from starting.
3. Move the lever (59) to the "COLD START" position (58)
(Fig. 17).
4. Pull the starter rope until engine runs.
5. Allow the engine to warm up for 4-10 seconds.
6. Depress the interlock then squeeze and release the
throttle trigger. This allows the choke to automatically
set to the "WARM START" position (57). Your unit is
now ready for use.
NOTE: The lever will automatically set to the "WARM
START" position after the throttle trigger is squeezed for
the first time.
TO START A WARM ENGINE:
1. Lay trimmer on a flat, bare surface.
2. Choke lever should already be in the "WARM START"
position. If not, squeeze and release throttle trigger.
Pull the starter rope until unit runs.
TO STOP THE ENGINE:
To stop the engine, depress the switch to the "O"
position.
30/09/03 17:00
I P NL S DK
English
MAINTENANCE
SPOOL REPLACEMENT
EZ LINE™ TAP ADVANCE SYSTEM
NEW PRE-WOUND SPOOL (Fig. 18 & 19)
If replacing string only, refer to "String Replacement" later
in this manual.
Use only 2.4 mm (0.095 in) diameter monofilament string.
Use the manufacturer's replacement string for best
performance.
1. Stop the engine and disconnect the sparking plug wire.
2. Remove the empty spool from the string head. Keep
3. To install the new spool, make sure the two strings are
4. Thread the strings into the eyelets in the string head.
5. Push down and turn the spool anticlockwise until it no
6. Make sure the string head and the spool retainer are
19
Page 19
N FIN GR H CZ
WARNING
Use only original manufacturer's replacement
parts, accessories and attachments. Failure to do
so can cause possible injury, poor performance
and may void your warranty.
You may make adjustments and repairs described here.
For other repairs, have the trimmer serviced by an
authorised service dealer.
Consequences of improper maintenance may include
excess carbon deposits resulting in loss of
performance and discharge of black oily residue
dripping from the silencer.
Make sure all guards, straps, deflectors and handles
are properly and securely attached to avoid the risk of
personal injury.
Hold the string head and unscrew the spool retainer.
Turn clockwise.
the spring attached to the spool.
captured in the slots opposite each other on the new
spool. Make sure the ends of each string are extended
approximately 152 mm (6 in) beyond each slot.
Carefully push the spool into the string head (gently pull
the strings to the outside if necessary). When the spool
is positioned in the string head, grasp the strings and
pull sharply to release them from the slots in the spool.
longer turns. Hold the spool down and rotate clockwise
a small amount. Release the spool. The spool should
be locked down in the string head. If not, hold down
and rotate until locked.
installed on the shaft by turning the retainer anti-
clockwise to tighten.
RUS RO PL