Homelite F-3045 Manual De Utilización página 21

Trimmer/Brushcutter-17 lgs
GB
F D E
DESCRIPTION
62. EYELETS
64. SPOOL
65. ARROWS ON SPOOL
66. ANCHOR HOLE
67. FIRST STRING
68. SECOND STRING
69. CLIPS
UNPACKING
INSTRUCTIONS
Carefully remove the product from the carton.
Inspect the product to make sure no breakage or
damage occurred during carriage.
Do not discard the packing material until you have
inspected and operated the product.
PACKING LIST FOR OWNER'S KIT
Grass deflector (2)
Blade guard (10)
Tri-Arc blade (11)
Shoulder strap (8)
Silencer guard (36), torque wrench (38) and screws (37)
Front "J" handle (15)
Holding pin (49)
Spanners - 13 mm (1/2 in) (51) and 16 mm (5/8 in) (45)
Fixings
Operator's manual
ASSEMBLY
ATTACHING THE POWER HEAD TO THE
TRIMMER ATTACHMENT (Fig. 2)
WARNING
Never attach or adjust any attachment while
power head is running. Failure to stop the engine
may cause serious personal injury.
The trimmer attachment connects to the power head by
means of a coupler device.
1. Loosen the knob (9) on the coupler (14) of the power
head shaft (13) and remove the end cap from the
attachment.
2. Push in the button located on the trimmer attachment
shaft. Align the button with the guide recess on the
power head coupler and slide the two shafts together.
30/09/03 17:00
I P NL S
English
70. BLADE PROTECTOR
71. PULL COVER TO OPEN
72. FILTER
73. AIR FILTER COVER
74. IDLE SPEED SCREW
75. LO NEEDLE
76. HIGH NEEDLE
Page 15
DK N FIN GR H
Rotate the trimmer attachment shaft until the button
locks into the positioning hole.
NOTE: If the button does not release completely in the
positioning hole, the shafts are not locked into place.
Slightly rotate from side to side until the button is locked
into place.
3. Tighten the knob securely.
WARNING
Be certain the knob is fully tightened before
operating equipment; check it periodically for
tightness during use to avoid serious injury.
REMOVING THE ATTACHMENT FROM THE
POWER HEAD
For removing or changing the attachment:
1. Loosen the knob.
2. Push in the button and twist the shafts to remove and
separate ends.
ATTACHING THE STORAGE HANGER (Fig. 3)
There are two ways to hang your attachment for storage.
To use the hanger cap (21), push in the button and
place the hanger cap over end of the lower end
attachment shaft. Slightly rotate the cap from side to
side until the button locks into place.
The secondary hole (22) in the attachment shaft can
also be used for hanging.
FRONT HANDLE (Fig. 4)
A barrier handle should be used for ensuring the best
control and maximising operator safety.
1. Hold the top (31) and bottom clamp (30) snugly in
position on the shaft housing so that handle will be
located to the operator's left.
2. Insert the end of the handle between the clamps.
3. Align the bolt holes and push the long bolt
(1/4-20 x 1 1/2 in) (25) through the handle side.
4. Place short bolt (1/4-20 x 1 in) (24) through opposite
side of clamp. Install flat washer (27), lock washers
(28) and hex nuts (29) to hold the assembly in place.
5. After assembly is complete, adjust the position of the
handle for best balance and comfort.
6. Tighten first the long bolt and then the short bolt.
7. Connect the shoulder strap to the strap hanger (7)
adjust to a comfortable position.
NOTE: Do not attempt to remove or modify the spacer (26).
This spacer limits the upper position of the handle grip.
15
CZ RUS RO PL