Names And Functions Of Each Part - Ibanez MiMX30 Manual De Instrucciones

Names and functions of each part

INPUT
1
This is a 1/4" phone input jack.
2 Preamp section
This controls the tone of the guitar. Details for each section are as follows.
 AMP SELECTION: This knob lets you select from eleven types of preamp mod-
els. For details, refer to the section describing the various amps.
 GAIN: This control knob adjusts the gain. The range of adjustment will depend
on the AMP SELECTION setting.
 Equalizer: These are the tone control knobs for the levels (BASS, MIDDLE,
TREBLE) of the three-band equalizer. The adjustable range and the function will
differ according to the AMP SELECTION setting.

Bank section
3
To save a sound you created, hold down the switch of the desired save-destination
channel for three seconds or longer. Details are described below.
 MANUAL switch: This switch selects manual mode, where all tone controls are
"what-you-see-is-what-you get".
 Channels (1-4): These buttons choose one of four channels in which you can
store your own settings.
* As an alternative to selecting these from the front panel, you can connect the
optional IFS2M(sold separately) foot controller and switch channels.
E-Tuner 
4
This is a simple tuner for your guitar's E string. Click the E-Tuner button. E-Tuner
mode is activated and FX or DELAY&REVERB function will be bypassed in this
mode. The illustrations below show the tuner LED motion as it operates.
12
 

The left side LED's indicate the pitch
is flat from E.
The middle three LED's simultane-
ously lit indicates in tune.
The right side LED's indicate the
pitch is sharp from E.
FX Section
5
Total 14 kinds of effects in 4 banks are available.

 SELECT knob: There are 4 FXs in each effect bank. You can select a parameter
in each FXs within their range. An "FX bank" table below shows details about
what you can select.
 MIX knob: You can control effect mix level, sensitivity or a sort of parameters as
showed in the FX bank table. When the MIX knob turned to all the way to the left,
effect is off.
* You can also switch the FX on/off by optional IFS2M(sold separately) foot con-
troller.
 TAP switch: This controls the modulation speed when a modulation type effect is
selected. The FX bank table shows when the TAP switch is active. When other
effects with inactive TAP feature is selected, the TAP switch is just lit.
* For details on TAP, refer to "TAP switch".
 FX bank access switch: FX bank select mode is activated by holding down this
switch more than 3 seconds.
 FX bank select switch: After above operation, you can select FX set from bank 1
to bank 4.
Bank Effect
FX1: Chorus1
FX2: Flanger
FX Bank 1
FX3: Vibrato
FX4: Step
FX1: Chorus1
FX2: Dynamic Flanger
FX Bank 2
FX3: Tremolo
FX4: Pitch Shifter
FX1: Chorus2
FX2: Auto Wah
FX Bank 3
FX3: Slow Attack
FX4: Phaser
FX1: Chorus2
FX2: Auto Resonance
FX Bank 4
FX3: Ring Modulator
FX4: Monophonic Pitch Shifter
5



Operation of Controllers
SELECT MIX TAP
Depth Mix Level Speed
Depth Mix Level Speed
Depth Mix Level Speed
Depth Mix Level Speed
Depth Mix Level Speed
Depth Sensitivity Speed
Depth Type Speed
Shift Mix Level N/A
Depth Mix Level Speed
Sensitivity Resonance N/A
Speed Type N/A
Tone Mix Level Speed
Depth Mix Level Speed
Sensitivity Resonance N/A
Modulation Mix Level N/A
Shift Mix Level N/A