Rear Panel - Fender Rumble 15 Instrucciones De Funcionamiento

� � � � � � � � � � � � � � � � � � �
Thanks for buying a Fender® Rumble™ series bass amplifier. Fender
50% 0 0 0
bass amplification provides thick, natural and balanced tone that
N DRIVE -15 +15 -15 +15 -15 +15 -15
PUNCH SCOOP
sits fat in your live or studio mix. Rumble amps are designed by
���� ���� ������� �������� ������
bass players. Full-featured and easy to operate, the Rumble family
gives you high-quality bass tone and incredible value.
5 0
2 8
0 10 -15 +15
����� � ����� ����
5
� �
2
0
������ � �����
A . INPUT 1 — Plug your passive or active bass in here. If
your bass is too hot and causes distortion, try using
INPUT 2.
B . INPUT 2 — A lower sensitivity input (-6dB) providing
more headroom to reduce distortion from high output
basses.
NOTE: Both INPUT 1 and 2 can be used simultaneously for
two instruments. In this situation, each input will have a
lower input sensitivity (-6dB).
C . VOLUME — Controls the loudness of the amplifier.
D . GAIN — Controls the amount of OVERDRIVE distortion.
F . BLEND — Controls the amount of distortion (set by
GAIN) to be blended with the clean bass signal. Lower
settings can maintain a cleaner tone, with some added
grit. Higher settings will produce more distorted tones
and add sustain.
E . ENABLE — Press this button to turn the OVERDRIVE
on or off. The red LED (light) illuminates when the
OVERDRIVE is on.
G . SHAPE FILTERS:
• PUNCH — Emphasizes tight punchy bass response,
useful for finger style playing or for enhancing the tonal
character of a bridge pickup.
• SCOOP — Mid-frequency cut, combined with low-and-
high-frequency boosts that offer a fat pleasing tone,
useful for slap style playing, low-volume practice, or in
combination with OVERDRIVE.
6
Rumble® 15 / 30 / 75 Bass Amps
0
+15
���� ����
���� ���� ����
������ ������ ��� ������ ���������
� � � � � � � � � � � �
0 0
-15 +15 -15 +15
���� ���� ����
��� ������ ������ ������ ���������
� � � � � � � � � � � � � �
5 50%
8 2 8
10 0 10 CLEAN DRIVE
ENABLE PUNCH SCOOP
���� �����
The Fender Precision Bass® Guitar was introduced in 1951, forever
changing music and giving birth to a new kind of musician—the
electric bassist. Since then music has never been the same. Your
�����
new Rumble will provide years of enjoyment as you continue your
musical journey and make history!
5
� �
2
0
������ � �����
�����
� � � � � � � � � � � �
0 0 0 0
-15 +15 -15 +15 -15 +15 -15 +15
���� ������� �������� ������
H . EQUALIZATION — Used to adjust overall tone and to
compensate for room acoustics. Remember, what sounds
harsh in one room may have just the right edge in
another room.
I . AUX IN — Plug your CD player or mp3 player in here.
The amp controls do not affect this input. Adjust the
volume or tone of the aux signal at its source.
J . HEADPHONES — Plug your stereo headphones (32
ohms minimum impedance) in here. Speaker output is
automatically disabled.
K . LINE OUT — Balanced output to connect to external
devices such as PA systems and recording consoles. Use
a balanced stereo cable (TRS→XLR or TRS→TRS) to reduce
noise and hum. Mono (unbalanced) cables can also be
used, but may be noisier. The level and tone of the LINE
OUT signal is affected by all pre-amp controls, including
Volume.
L . FOOTSWITCH — Allows for remote switching of
OVERDRIVE. See the following page for details.
M . POWER — Switches the amplifier ON/OFF as indicated
by the power light.
N . IEC POWER CORD SOCKET — Connect the included
power cord to a grounded A/C electrical
outlet in accordance with the voltage and
frequency ratings specified on the rear
panel of your amplifier.
fender.com
� � � � � � � � � � � � � � � � � � � � �
5 50% 0 0 0
8 2 8
10 0 10 CLEAN DRIVE -15 +15 -15 +15 -15 +15
ENABLE
���� ����� ���� ��� ������
���� ���� ����
������ ������ ��� ������

Rear Panel

���� ���� ����
������ ������ ��������� �����
���� ����
��������� �����