Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ENGLISH (
Original Instructions)
1 Instruction manual
♦ Check for damage to the tool, parts or accessories
which may have occurred during transport.
♦ Take the time to thoroughly read and understand this
manual prior to operation.
ELECTRICAL SAFETY
Your tool is double insulated; therefore no earth wire
is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must be
replaced by the manufacturer, authorized Stanley
Service Center or an equally qualified person in
order to avoid damage or injury. If the power cord is replaced
by an equally qualified person, but not authorized by
Stanley the warranty will not be valid.
USING AN EXTENSION CABLE
If it is necessary to use an extension cable, please used
an approved extension cable that fits the tool's power input
specifications. The minimum cross-sectional area of the
conducting wire is 1.5 sq. mm. Cables should be untangled
before reeling up.
Cable cross-sectional
area (mm
)
2
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes Cable rated current (Ampere)
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
18
Cable rated current
(Ampere)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
6
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
FEATURES (FIG. A, FIG. D, FIG. F, FIG. G)
This tool includes some or all of the following features.
1. Main handle
2. Lock-on button
3. Variable speed switch
4. Forward/Reverse lever
5. Mode selector switch
6. Sleeve
7. Tool clamp
8. Depth Stop
9. Side handle
10. Date code
11. SDS Plus bit
12. Drill chuck
13. Drill bit
14. Dust collector
15. Locking collar
16. SDS Plus Tool Holder
17. Keyless chuck
ASSEMBLY
WARNING! Before assembly, make sure that the tool is
switched off and unplugged.
Attaching the Side Handle (FIG. A)
WARNING! When using the tool, please use the side
handle (9) for your safety.
The side handle can be fitted to suit both right-handed and
left-handled users.
♦ Turn the grip counter-clockwise until you can slide the
side handle onto the front of the tool.
♦ Rotate the side handle into the desired position.
♦ Tighten the side handle by turning the grip clockwise.
60
WARNING! When using the tool, remember to install the
side handles properly.
10
Fitting an accessory (FIG. A)
♦ Clean and grease the shank (11) of the SDS Plus bit.
15
♦ Insert the accessory bar into the tool clamp(7).
20
♦ Push the accessory down and turn it slightly until it fits
25
into the slots.
♦ Pull on the accessory to check if it is properly locked. The
-
hammering and drilling function requires the accessory
to be able to move axially several centimetres when
-
locked in the tool clamp.
6
♦ To remove the accessory, pull back the sleeve (6) and
pull out the accessory from the tool clamp.
6
Fitting the dust collector (Fig. F)
15
♦ Insert the accessory bar (11) into dust collector (14), then insert the
15
accessory bar (11) with dust collector into tool clamp (7).
20
♦ Only using the unit upwardly is necessary to use the
dust collect like Fig. F.
-
Tabla de contenido
