Carat SL-1506 Manual página 7

MAIN PARTS
The main parts are numbered identical to the graphics of
the power tool at page 2 of this manual.
1. Handle
2. Overload indication
3. ON/OFF Switch
4. Dust extraction
5. Carbon brush holder
6. Cutting depth adjustment
7. Laser guide
8. Blade guard
9. Wheels
SPECIFICATIONS
Type
Rated power input
Protection class
Loaded speed
Arbor diameter
Maximum diameter diamond cut-off wheel
Maximum cutting depth
Maximum cutting width
Weight
INTENDED USE
The SL-1506 is a double insulated handheld wall chaser
for dry use in combination with sawblades for cutting in
mineral materials such as concrete or brick.
The machine is only suitable for use with saw blades with
laser welded diamond segments.
POWER SUPPLY
The tool should be connected only to a power supply of the
same voltage as indicated on the nameplate, and can only
be operated on single-phase AC supply. This is a class II
tool and can therefore also be used from non-grounded
sockets.
ENVIRONMENTAL PROTECTION
Do not dispose of electric tools together
with household waste material! In obser-
vance of European Directive 2012/19/EU
on waste electrical an electronic equip-
ment and its implementation in accordance with national
law, electric tools that have reached the end of their life
must be collected separately and returned to an environ-
mentally compatible recycling facility.
WORKING PROCES
The fi gures referenced to, are stated at page 3 of this ma-
nual.
Dust extraction
Dust released during dry cutting is dangerous to your he-
alth. Therefore a dust extraction system specially intended
for this purpose must be used.
The use of a dust extraction system is also required to op-
timize the life time of the diamond saw blades.
To prevent clogging of the dust extraction system it is es-
sential that the materials which are being cut are comple-
tely dry.
Information about dust extraction systems is available at
your local Carat dealer.
NMHX030
16-08-2018
Laser guide system
The SL-1506 is equipped with a laser guide integrated in
the blade guard. The laser is activated as soon as the on/
off switch is pressed and the sawblades start rotating. The
laser shows as a red line on wall "in front of the machine"
and indicates the cutting line of the inner blade (nearest
to the motor)
The visibility of the laser can be increased by wearing spe-
cial "laser" goggles (info at your Carat dealer). The laser
is class 2 / 1mW and approved for use on hand held ma-
chines.
Mounting diamond grinding wheels
For mounting the diamond grinding wheels do as
SL-1506
follows:
2000W
II
Note: The SL-1506 is only suitable to use in combi-
4200 rpm
nation with six diamond grinding wheels, each with a
Ø 22,2 mm
core thickness of 1,5mm.
Ø 150 mm
50 mm
• Loosen the bolts of the blade guard.
2,4 - 50 mm
• Take of the outer part of the blade guard.
6,7 kg
• Loosen the bolt with a spanner, while blocking the
locking fl ange with the two-pin spanner.
• Remove all fl anges.
• Position the fi rst diamond grinding wheel.
• Position the fi rst fl ange with a thickness of 2,1mm.
• Position the following fi ve diamond grinding wheels,
and the other four intermediate fl anges with a thick-
ness of 2,1mm.
• Position the remaining fl anges.
• Position the locking fl ange.
• Mount the bolt.
• Thighten the bolt with the spanner, while blocking the
blocking fl ange with the two-pin spanner.
• Place the outer part of the blade guard.
• Mount en thighten the bolts of the blade guard.
Always check the arbor hole and the fl anges before moun-
ting the diamond grinding wheel. They must be clean and
undamaged.
Note: make sure that saw blades are used intended for
dry use and suited for the material which has to be cut
ask your carat dealer for advice!
Adjusting cutting depth [Fig. A]
Release knob (1).
Adjust depth.
Fasten knob (1).
Making horizontal and vertical cuts
Before making a cut always check for hidden water, gas
pipes and electricity loads in the wall.
Defi ne the position of the cut.
To determine the location of the diamond grinding wheels
a indication line is made on the guard. This line represents
the inner diamond grinding wheel.
Place the machine with the side of the pivot against the
wall or fl oor in such way the diamond grinding wheel can
turn freely.
Turn on the machine and make sure the diamond grinding
wheels rotate at full speed.
Slowly push the diamond grinding wheels into the material.
ENGLISH – ORIGINAL INSTRUCTIONS
7