Worx Sonicrafter WX671 Manual Del Usuario página 10

OPERATION INSTRuCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The power tool is intended for sawing and
separating wooden materials, plastic, plaster,
non-ferrous metals and fasteners (e.g.
nails and clamps) as well as for working on
soft wall tiles and for dry grinding of small
surfaces. It is especially suitable for working
close to edges and for flush cutting.
wARNING: Before working your
tool make sure that no power cords
will be damaged. Unplug your tools before
mounting or replacing accessories.
Do not touch the gear box after long working
time, because it could be hot.
1. MOUNTING THE TOOL (See Fig. A1, A2)
cAUTION: For all work or when
changing application tools, always wear
protective gloves. Avoid danger of injury
from the sharp edges of the application tools.
10
Application tools can become very hot while
working, presenting danger of burns!
wARNING: To reduce the risk of
injury, do not let the Universal end
cut blades or any segment saw blades
face back toward the user's hand.
Unscrew the fastening piece (5).
Clean the tool holder, the application tool and
the fastening piece (5).
Place the application tool exactly onto the hex-
shaped tool holder. Note that the application
tool has a flush fit.
Reposition the fastening piece (5) using the
supplied Allen key.
2. USING ADAPTER (19) (See Fig. A3)
Accessories of other brands( Fein
can be fitted onto the Sonicrafter
using the adapter.
NOTE: Fein is a registered trademark of C. &
E. Fein GmbH. Bosch is a registered trademark
of Robert Bosch GmbH.
1) Use the allen key (21) to unscrew the
fastening piece (5) and then remove it from
High frequency multi-function tool
the tool holder .
2) Clean the tool holder, the adapter the
application tool and the fastening piece.
3) Fit the adapter onto the tool holder, then
place the application tool onto the adapter.
Make sure that the tool holder, the adaptor,
and the application tool share a flush fit.
4) Reposition the fastening piece onto the
application tool and tighten with the allen key.
NOTE: Make sure the adapter matches the
application tool. The adapter (I) is matched to
the application tool of Fein
is matched to the application tool of Bosch
(See Fig. A3)
3. MOUNTING/cHANGING THE SANDING
SHEET (See Fig. B1,B2)
Align the sanding sheet and press it onto the
sanding pad by hand.
Firmly press the power tool with the sanding
sheet against a flat surface and briefly switch
the power tool on. This provides for good
adhesion and prevents premature wear.
If one point has become worn, pull off the
sanding sheet, turn it 120° and place it on
again.
4. OPERATING THE ON/OFF SwITcH
To start the machine, push the On/Off switch
(1) forward so that the "I" is indicated on the
switch.
To switch off the machine, push the On/Off
switch (1) toward the rear so that the "0" is
indicated on the switch.
5. USING THE VARIABLE SPEED
cONTROL (wX671 wX671.1 wX671.2
wX671.3 wX671.4 wX671.5 wX671.6
wX671.7 wX671.8 wX671.11)
Select oscillation frequency (speed) while the
motor is running.
The variable speed control (2) can be used
® ®
, Bosch )
to set the optimum oscillating frequency
®
brand tool
according to the accessories used and the
respective application.
High oscillation frequency:
Sanding, sawing, rasping and polishing stone
and metal.
Low oscillation frequency:
Polishing varnishes.
®
. The adapter (II)
®
.
EN