Safety Warnings Specific For Sanding Operations - Metabo WEVF 10-125 Quick Inox Manual De Instrucciones

and carefully re-enter the cut. The wheel may
bind, walk up or kickback if the power tool is
restarted in the workpiece.
e) Support panels or any oversized workpiece
to minimize the risk of cutting disc pinching
and kickback. Large workpieces tend to sag under
their own weight. Supports must be placed under
the workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
f) Use extra caution when making "pocket cuts"
into existing walls or other blind areas. The
protruding cutting disc may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
4.5 Safety Warnings Specific for Sanding
Operations:
a) Do not use excessively oversized sanding
disc paper. Follow manufacturers
recommendations, when selecting sanding
paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may
cause snagging, tearing of the disc or kickback.
4.6 Safety Warnings Specific for Wire
Brushing Operations:
a) Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work load
and centrifugal forces.
4.7 Additional Safety Instructions:
WARNING – Always wear protective
goggles.
Use elastic cushioning layers if they have been
supplied with the grinding media and if required.
Observe the specifications of the tool or accessory
manufacturer! Protect the discs from grease or
impacts!
Grinding wheels must be stored and handled with
care in accordance with the manufacturer's
instructions.
Never use cutting discs for roughing work! Do not
apply pressure to the side of the cutting discs.
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must
be sufficiently supported.
If accessories with threaded inserts are used, the
end of the spindle may not touch the base of the
hole on the grinding tool. Make sure that the thread
in the accessory is long enough to accommodate
the full length of the spindle. The thread in the
accessory must match the thread on the spindle.
See page 4 and chapter 14. Technical
Specifications for more information on the spindle
length and thread.
Use of a fixed extractor system is recommended.
Always install an RCD with a maximum trip current
of 30 mA upstream. If the angle grinder is shut down
via the RCD, it must be checked and cleaned. See
chapter 9. Cleaning.
Damaged, eccentric or vibrating tools must not be
used.
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked side handle must be
replaced. Never operate a machine with a defective
side handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
Secure small workpieces. For example, clamp in a
vice.
This power tool is not suitable for polishing work.
Improper use of the machine will void the warranty!
The motor may overheat and damage the electric
power tool. We recommend using our angle
polisher for polishing work.
The accessory may not be fastened with a two-hole
nut for safety reasons. Only use the (tool-free)
clamping nut (2).
Reducing dust exposure:
Some of the particles generated using this
power tool may contain substances known to
cause cancer, allergic reactions, respiratory
diseases, birth defects or other reproductive harm.
Some of these substances include: Lead (in paint
containing lead), mineral dust (from bricks,
concrete etc.), additives used for wood treatment
(chromate, wood preservatives), some wood types
(such as oak or beech dust), metals, asbestos.
The risk from exposure to such substances will
depend on how long the user or nearby persons are
being exposed.
Do not let particles enter the body.
Do the following to reduce exposure to these
substances: Ensure good ventilation of the
workplace and wear appropriate protective
equipment, such as respirators able to filter
microscopically small particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work (see chapter 11.), thus less particles enter the
environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers.
ENGLISH en
15