Tabla de contenido
Idiomas disponibles
Idiomas disponibles
This manual is designed to make it as easy as possible for you
to assemble, install, operate, and maintain your ceiling fan
Tools Needed for Assembly
• One Phillips head screwdriver
• One stepladder
• One ¼˝ blade screwdriver
• One wire stripper
NOTE: Assemble with Hand tools Only!
▲WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 8). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
s
e t
p
s
h
a
v
e
b
e
e
n
c
o
m
p
e l
▲WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer to
parts list/exploded view illustration. (Pages 16,17)
Hanger Bracket
Assembly
Blade Holders
(2 sets)
NOTE: The illustration shown is not to scale or its actual configuration may vary, blade sets are sold separately.
• Four wire connectors
(supplied)
•
⁄
˝
½˝ &
⁄
˝ wrench
7
,
9
16
16
or socket wrench
Unpacking Instructions
e t
d
a
n
d
w
l l i
b
e
h
l e
f p
l u
n i
Ceiling
Support Bar
Canopy
Assembly
Switch Housing
Assembly (2)
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3-
conductor (2-wire with ground) of the following size:
Installed Wire Length
NOTE: Place the parts from the loose parts bags in a small con-
tainer to keep them from being lost. If any parts are missing,
contact your local retailer.
DAMP LOCATION CEILING FAN: If you have purchased a
Damp Location Ceiling Fan, you may only use light kits marked
suitable for use in damp locations.
f
n i
d
n i
g
y
o
r u
p
a l
c
e
s
h
o
u
d l
• Hanger Bracket Assembly
• Ceiling Canopy
• 24˝ Downrod/Ball Assembly
•
Support Bar Assembly
• Two Motor Assemblies
• Two Switch Cup Assemblies
• Blade Holder pack containing:
– Five blade holders (red dot)
– Five blade holders (white dot)
– Ten blade arm covers
• Blade Cover Mounting Hardware Bag
– 3/16˝-24 carriage head nut (21)
– 3/16˝-24 x 17mm washer-head
screws & fiber washers (21)
• Blade to Motor Hardware Bag
– ¼–20 x 11mm Cap head
screws (21)
– Fanimation screwdriver
• 2-speed, CW3WH-CA wall control
24
˝
Motor Assembly (2)
3
Materials
Wire Size A.W.G.
Up to 50 ft.
50 - 100 ft.
y
o
u
b
e
i
t n
r e
u r
p
e t
. d
• Support Cable bag:
– Ceiling Support Cable
– Cable Clamp (3)
– 4˝ lag bolt
–
⁄
˝ flat washer
3
8
• Hardware bag:
– 2˝ lag bolt
– 5 mm Allen wrench
– Two
5
– Two
5
– Two
5
– Six motor mounting screws
– One ¼˝–20 x 2
– One ¼˝–20 nylon lock nut
– Four wire connectors
Downrod Assembly
Hardware Bag
14
12
⁄
˝–32 x 1˝ threaded rods
32
⁄
˝–32 external lockwashers
32
⁄
˝ knurled knobs
32
⁄
˝ cap head screw
1
8
2-Speed
CW3WH-CA
Wall Control
Capítulos
Tabla de contenido
Solución de problemas
