DeWalt DWOAS6PS Manual De Instrucciones página 13

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

the chain before performing the following operations.
Failure to do this could result in serious personal injury.
Combining the powerhead 
 14 
attachment 
 1 
creates a pole saw that is approximately 5.9 ft
(1.8 m) in length.
To Attach the Powerhead to the Pole
Saw Attachment
1. The upper powerhead pole 
latching holes 
 15 
 16 
 17 
2. When installing the pole saw attachment pole 
into the upper powerhead pole 
latching button
 18 
with one of the three latching
holes 
 15 
 16 
 17 
.
nOTE: To properly engage the latching button
the latching hole 
 15 
, slightly rotate the powerhead
pole 
 14 
and move it axially until the latching button
engages the latching hole.
3. Turn the knob 
 13 
to secure the attachment.
4. When properly assembled, the latching button should
engage with one of the three latching holes. If it does
not, do not use, disassemble and re‑align the pole saw
attachment 
 1 
so the latching button 
one of the three latching holes 
Assembling the Extension Pole to the Pole
Saw Attachment and the Powerhead
(Fig. B, C)

CAUTION: The extension pole should exclusively be
used with the pole saw attachment.

CAUTION: Only one extension pole should be used
with the pole saw attachment.
To Attach the Powerhead to the Pole
Saw Attachment
Adding the extension pole 
 11 
and pole saw attachment 
 1 
approximately 8.9 ft (2.7 m) in length.
To Attach the Powerhead to the
Extension Pole and Pole Saw Attachment
1. The upper powerhead pole 
latching holes 
 15 
 16 
 17 
2. When installing the extension pole 
powerhead pole 
 14
and align the latching button
with one of the three latching holes 
3. Turn the knob 
 13 
to secure the extension pole.
To Attach the Pole saw Attachment to the Extension Pole:
1. When installing the pole saw attachment
extension pole 
, the pole saw attachment pole 
 11 
equipped with three latching holes 
latching button 
 18 
.
2. When installing the pole saw attachment pole 
extension pole 
 11 
and align the latching button
one of the three latching holes 
3. Turn the knob 
 13 
to secure the attachment.
to the pole saw
 14 
is equipped with three
for the latching button 
 18 
 1 
 14 
and align the
 18 
with
 18 
engages with
 15 
 16 
 17 
.
to the powerhead 
 14 
creates a pole saw that is
 14 
is equipped with three
for the latching button 
 18 
 11 
into the upper
 18 
 15 
 16 
 17 
.
into the
is
 1 
 15 
 16 
 17 
for the
 1 
into the
 18 
with
 15 
 16 
 17 
.
4. When properly assembled, the latching button should
engage with one of the three latching holes. If it does
not, do not use, disassemble and re‑align the pole saw
attachment 
 1 
so the latching button 
of the three latching holes 
pole coupler 
 12 
.

WARNING: Always check to make sure that the knobs
are completely secured in place. If the knobs are not
completely secured it could result in the assemblies
.
becoming disconnected creating a hazardous
condition. Periodically check the connections to ensure
that the knobs are completely secured in place.
DISASSEMBLY

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Detaching Pole Saw Assembly (Fig. A–C)

WARNING: Sharp moving blade. To prevent accidental
operation, insure that battery is disconnected from the
handle and that the protective scabbard is in place on
the chain before performing the following operations.
Failure to do this could result in serious personal injury.
When detaching the assemblies, always detach the pole saw
attachment 
 1 
first.
To Remove the Extension Pole from the Pole
saw Attachment:
1. Install scabbard 
 32 
2. When removing the pole saw attachment 
extension pole 
 11 
3. Depress the latching button 
pole coupler 
 12 
, and pull the pole saw attachment
away from the extension pole 
To Remove the Powerhead from the extension pole:
1. When removing the extension pole 
powerhead 
 14 
, loosen the knob 
latching button 
 18 
from the powerhead 
Installing the Guide Bar and Saw Chain
.
(Fig. D–G)

CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can
cut you when it is not running.

WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to
do this could result in serious personal injury.
If the saw chain 
 7 
and guide bar 
the carton, the chain has to be attached to the bar, and both
must be attached to the body of the tool.
1. Place the pole saw attachment 
2. Rotate the bar lock nuts 
13 mm wrench (not provided) and remove them.
English
 18 
engages one
 15 
 16 
 17 
in the extension
on guide bar and chain.
from the
 1 
, loosen the knob 
 13 
.
 18 
located on the extension
 11 
.
 11 
from the
 13 
. Then depress the
and pull the extension pole 
 11 
 14 
.
 6 
are packed separately in
 1 
on a flat, firm surface.
 3 
counterclockwise with a
away
11
Tabla de contenido
loading

Tabla de contenido