Specified Conditions Of Use; Residual Risk; Know Your Product - AEG BPS18-254BL Manual Original

Do not attempt to repair the laser device by yourself.
Do not attempt to change any parts of the laser device by yourself.
Any repairs must only be carried out by the manufacturer or
authorised service agent.
WARNING Do not replace the installed laser with a di erent type.
Do not point laser at re ective surfaces,
Avoid exposure to laser radiation. Laser may emit hazardous
radiation.

SPECIFIED CONDITIONS OF USE

The slide compound mitre saw is intended for sawing solid
and bonded wood with or without glued veneer, plastics, and
materials similar to wood.
The slide compound mitre saw is intended to be used only by adult
operators who have read the instruction manual and understand
the risks and hazards.
The slide compound mitre saw is designed to be xed at the base
to a solid bench top. If the base is not securely xed, the whole
machine may move during cutting operations, which increases
the possibility of serious personal injury.
GB
The slide compound mitre saw is designed make bevel and
mitre cuts. The capacities for the various cuts are provided in the
product speci cations in this manual.
The slide compound mitre saw is to be used in dry conditions, with
excellent ambient lighting and adequate ventilation.
The slide compound mitre saw is intended for consumer use and
should only be used as described above and is not intended for any
other purpose.

RESIDUAL RISK

Even when the slide compound mitre saw is used as prescribed,
it is still impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator should
pay special attention to avoid the following:
• Risk of contact with uncovered parts of the rotating saw blade.
• Kick-back of work pieces or parts of work pieces due to improper
adjustment or handling.
• Catapulting of faulty carbide tips from the saw blade. Wear Eye
protection at all times.
• Damage to the respiratory system. Wear respiratory protection
masks containing lters appropriate to the materials being
worked. Ensure adequate workplace ventilation. Do not eat,
drink or smoke in the work area.
• Damage to hearing if e ective hearing protection is not worn.
WARNING Dust from certain paints, coatings, and materials may
cause irritation or allergic reactions. Dust from wood such as oak,
beech, MDF, and others are carcinogenic. Materials containing
asbestos should only be worked on or processed by quali ed
specialist operators.
WARNING Injuries may be caused or aggravated by prolonged use
of a tool. When using any tool for prolonged periods, ensure you
take regular breaks.
English
32

KNOW YOUR PRODUCT

See page A.
1. Handle, insulated gripping
surface
2. Laser switch
3. LED switch
4. Saw blade
5. LED light
6. Spindle lock button
7. Switch trigger
8. Lower guard lock out lever
9. Upper guard
10. Laser guide
11. Lower guard
12. Mouting hole
13. Right sliding fence
14. Extension bar
15. Right sliding fence
16. "No hands zone" label
17. Mitre lock knob
18. Turn table lock handle
19. Balancing foot
20. Kerf plate
21. Mitre scale
22. Turntable
23. Saw base
REPLACEMENT LIST
• BPS18-254 BL: Mitresaw EN 847-1/ ø254 x ø30 x 2,2 / 48T / HW /
n max. 7400 min-1 (Page A: No. 4)
• Kerf plate (Page A: No. 20)
BATTERIES
Use only System GBS chargers for charging System GBS battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after use.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery
pack where the temperature is below 27°C and away from mois-
ture Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
24. Blade wrench
25. Fixed fence
26. Left sliding fence
27. Clamp
28. Bevel scale
29. Depth stop
30. Head lock pin
31. Depth control knob
32. Sliding fence adjustment
knob
33. Slide bar
34. Dust bag
35. Carrying handle
36. Battery pack
37. Sliding fence adjustment
knob
38. Bevel lock knob
39. Single/dual bevel selector
40. Screws for xing fence
41. 0° bevel stop screw
42. Right bevel angle adjusting
screw
43. Left bevel angle adjusting
screw